亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stroke adjustable cylinder Sold to Malaysia

Release time:2023-11-09 08:46:15 Hits: Current position: Home > News

This article mainly introduces:

Malaysia hydraulic cylinder,stroke adjustable cylinder manufacturer,stroke adjustable cylinder

Malaysia stroke adjustable cylinder

(Malaysia stroke adjustable cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stroke adjustable cylinder are widely used in Malaysia,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed stroke adjustable cylinder for customers from Malaysia.

Introduction to stroke adjustable cylinder:

Repair method of small range wear of oil stroke adjustable cylinder: 1. Use oxygen-acetylene flame to bake the scratched part (master the temperature, avoid surface annealing), bake the oil on the metal surface all the year round until no sparks splash; 2. The scratched part is treated with an Angle grinder, the grinding depth is more than 1 mm, and the groove is polished along the guide rail, preferably a dovetail groove. Scratch both ends of the drilling deeper, change the force situation; 3. Clean the surface with absorbent cotton dipped in acetone or anhydrous ethanol.

In the process of using the stroke adjustable cylinder, sometimes such a problem will occur, the stroke adjustable cylinder can not act immediately after the instruction of the stroke adjustable cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil stroke adjustable cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

When the stroke adjustable cylinder is installed, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the stroke adjustable cylinder head, earring (or middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent rigid interference and cause unnecessary damage.

stroke adjustable cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the stroke adjustable cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

Answers to some questions about stroke adjustable cylinder:

Cylinder pressure calculation formula
The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate it according to the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the working pressure P (unit MPa) the thrust of the cylinder F push =3.14*R*R*P (unit N) The pulling force of the cylinder F pull =3.14* (R*R-r* R) *P (unit N).

How to calculate the tonnage of the hydraulic press? Example: The input cylinder pressure is 5Mpa, the end area of the cylinder piston is 100mm, and how much is the thrust tonnage?
F=P*S=5*10^6*3.14*(1/20)^2=39250N.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
熟妇网站大全| AV片传媒在线| 国产精品不卡2025一区| 丁香婷婷色五月| 操小女逼视频| 国产一级黄色录像| 小黄片污污在线观看高h np| 成人和精品视频在线一区二区| 2021美女免费福利视频| 骚货轮奸视频| 黑人大鸡巴暴操日本美女淫逼视频 | 做暧暧欧美日韩| 一区二区三区在线观看天堂| 欧美大BB视频| 欧洲一区二区久| 日本久久婷婷| 亚洲a青草苹果v| 免费进入网站18 国产| 婷婷五月六月综合激情| 啊啊好舒服我要视频| 亚洲成人精品不卡中文字幕| 欧美性妇一区二区| 鸡巴操穴流白浆视频| 人人上人人摸人人舔| 激情久久黄色| ww天天日| 91无码人妻精品一区二区| 色综合一区色色中文字幕| 中国美女干大逼| 91鸡巴插小穴视频亚洲一起操| 超碰奶子在线观看| 中文字幕一二三四区视频| 欧美国产日韩综合在线| 国产一二三视频网址| 男人乱操女人逼的视频| 久久六十熟女| 婷婷综合福利| 淑女人妻在线| 亚洲综合在线| 淄博市| 华语大鸡巴日逼|