亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

drilling truck cylinder Sold to Turkey

Release time:2023-11-12 15:33:10 Hits: Current position: Home > News

This article mainly introduces:

Turkey hydraulic cylinder,drilling truck cylinder manufacturer,drilling truck cylinder

Turkey drilling truck cylinder

(Turkey drilling truck cylinder,produced by Hengyu Group)

drilling truck cylinder are widely used in Turkey,because of high work efficiency,long service life,smooth movement.So our company has designed drilling truck cylinder for customers from Turkey.

Introduction to drilling truck cylinder:

The viscosity of the working oil used in the drilling truck cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

If the drilling truck cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the drilling truck cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow drilling truck cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the drilling truck cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the drilling truck cylinder includes the leakage caused by excessive wear of the drilling truck cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and drilling truck cylinder, and the phenomenon of "pulling the drilling truck cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

In order to ensure the service life of the drilling truck cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

The advantages and disadvantages of the drilling truck cylinder: the surface of the drilling truck cylinder by painting, coating protection treatment, bright luster is not easy to rust, all raw materials of the drilling truck cylinder through the top heat treatment, high manufacturing precision, belongs to the precision machinery, has a simple structure, stable quality, high mechanical efficiency, easy to achieve automation and many other advantages. However, hydraulic technology also has the shortcomings of oil leakage, oil temperature change affecting the control of running speed, noise, expensive cost and high maintenance cost.

Answers to some questions about drilling truck cylinder:

What is the rated pressure of the general cylinder?
This depends on the model of the cylinder, 1. The rated pressure of the light tie rod cylinder is 7 series 7MPa and 14 series 14MPa. 2. Rated pressure of engineering cylinder 16MPa. 3. Rexroth type metallurgical cylinder rated pressure 250MPa.

What is the difference between hollow and solid oil cylinders?
Hollow solid cylinder, according to conventional understanding, refers to whether the piston rod is solid or hollow. General ordinary hydraulic cylinder, the piston rod is solid structure. Hollow hydraulic cylinder refers to a hollow piston rod structure of the hydraulic cylinder, see the attached figure. Piston rod hollow function: 1, the piston rod hollow, the middle can be threaded rod. For example, the clamping cylinder with a sawing machine, the piston rod center threading rod, part of the stroke through manual, part of the stroke hydraulic automatic walk. 2, the hollow hole of the piston rod can be used to direct the oil circuit to achieve special oil circuit. 3, the cylinder is relatively large, the piston rod is relatively large, and the stroke is longer, in this case, the piston rod is hollow to reduce the movement friction and lateral force.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲爱爱无码视频| 欧美日本鸡巴操穴| 高潮艹逼啊~啊啊视频| 插清纯美女逼逼| 熟女在线视频精品| 成人AV导航链接| 久久综合97婷婷五月手机免费观看| 操我视频啊啊啊| 中文字幕 有码 Av| 免费黄色污网址啊啊啊?| 操逼逼伊人| 奶子久久| 天天干天天射影院| 91男人大香蕉| 日韩少妇免费视频 | 日本 有码 在线播放| 欧美日韩啊啊啊啊精品 | 日本一区、二区不卡视频| AV伊人湿乐园| 夜夜嗨精品免费| 亚洲电影网一区二区| 啊啊操我日逼| 欧美 日韩 变态 另类| 亚洲五月婷婷图片| 亚洲欧洲视频成人| 国产一区二区啪啪| 国产91精品福利在线观看| 国产激情文学网| 国产美女福利啪啪视频| 色欲av火龙果一区二区| 北岛玲人妻在线| 点击进入午夜福利18在线| 骚逼磨鸡巴观看| 日韩阴毛成人视频| 国产叼嘿视频一区二区三区| 亚洲日韩免费一区视频| 爱爱精品视频| 亚洲 丝袜 一区 偷拍| baoyu118 无码 欧美| 好爽免费日本| 宁陕县|