亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Peru

Release time:2023-11-09 08:46:15 Hits: Current position: Home > News

This article mainly introduces:

Peru hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Peru swager cylinder

(Peru swager cylinder,produced by Hengyu Hydraulic Co., Ltd)

swager cylinder are widely used in Peru,because of no need for deceleration device,smooth movement,long service life.So our company has designed swager cylinder for customers from Peru.

Introduction to swager cylinder:

If the swager cylinder slips or crawls, please check whether there is astringency inside the swager cylinder, because the internal parts of the swager cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the swager cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the swager cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

Factors that should be considered when selecting the oil seal in the swager cylinder: some specific factors should be taken into account when selecting the oil seal in the swager cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: swager cylinder diameter, piston rod diameter, piston rod and piston groove size, swager cylinder working pressure, swager cylinder movement speed, hydraulic system oil temperature and swager cylinder working environment.

When producing oil swager cylinders, there are two processing processes, grinding and rolling, the latter is better than the former. Rolling machining is a kind of non-cutting machining, using the plastic deformation of the metal at room temperature, so that the micro roughness of the workpiece surface is flattened to achieve the purpose of changing the surface structure, mechanical characteristics, shape and size. Therefore, this method can achieve the two purposes of finishing and strengthening at the same time, which can not be done by grinding.

The wear of the hard chromium plating layer of the swager cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

Answers to some questions about swager cylinder:

How to disassemble the cylinder?
Generally speaking, it is not difficult to disassemble the hydraulic cylinder, as long as you are careful, but you often encounter some small trouble in the disassembly process, because the disassembly process is not correct. In fact, this can be avoided, as long as you follow below points. 1. Before removing the hydraulic cylinder, the hydraulic circuit should be relieved of pressure, otherwise, when the oil pipe connected with the cylinder is loosened, the high-pressure oil in the circuit will be rapidly ejected. When the hydraulic pressure comes back, the handwheel or pressure regulating screw at the relief valve should be loosened first, so that the pressure oil is unloaded, and then the power supply or power source is cut off, so that the hydraulic device stops running. 2. Disassembly should prevent damage to the top thread of the piston rod, the oil thread and the chrome layer on the piston rod surface.

Cylinder pressure calculation formula
The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate it according to the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the working pressure P (unit MPa) the thrust of the cylinder F push =3.14*R*R*P (unit N) The pulling force of the cylinder F pull =3.14* (R*R-r* R) *P (unit N).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
少妇骚B自慰| 手机大香蕉在线视频| 嗯嗯嗯好爽免费视频在线观看| 大鸡吧操逼图片视频| 免费大鸡巴操小屄视频| 国产性爱第一区| 欧美曰韩视频一级毛片在线| 日本女人与黑人男子在厨房| 91精品国产综合久蜜臀| 免费观看在线日B视频| 蜜臀av午夜一区二区三区gif| 北条麻妃蜜臀一区二区| 美女日b国产一| 美女穿丝袜av| 大黑鸡吧操中国美女| 日本精品成人一区二区三区| 日本大香焦巨乳在| 色屁屁一区二区三区视频国产色湿淫 | 亚洲∨∧| 抽插校花的小穴中文字幕专区91| AV操逼视屏| 日欧美美女被干视频| 大香蕉一本在线中文| 美女被屌草| 美女逼逼的视频| 在线主播美女极品美泬| 草草草视频免费| 刘玥 一区二区三区视频| 男女嫩操AV| 插播B视频| 亚洲骚妇一区二区在线观看| 欧日韩免费| 奶头无遮盖国产| 西藏| 在线一二三av| 黄色国产视频网| 日韩视频少妇麻豆传媒| 日韩妇自慰| 婷婷欧美拍| 国产淫妇av| 国产AV九区|