亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

self-locking hydraulic cylinder Sold to Belarus

Release time:2023-11-09 08:46:16 Hits: Current position: Home > News

This article mainly introduces:

Belarus hydraulic cylinder,self-locking hydraulic cylinder manufacturer,self-locking hydraulic cylinder

Belarus self-locking hydraulic cylinder

(Belarus self-locking hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

self-locking hydraulic cylinder are widely used in Belarus,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed self-locking hydraulic cylinder for customers from Belarus.

Introduction to self-locking hydraulic cylinder:

The repair method of the self-locking hydraulic cylinder: the repair of the self-locking hydraulic cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

self-locking hydraulic cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the self-locking hydraulic cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

The self-locking hydraulic cylinder is mainly composed of body, piston, piston rod, self-locking hydraulic cylinder head, self-locking hydraulic cylinder bottom, piston rod head and related auxiliary devices. The piston divides the self-locking hydraulic cylinder into two chambers, and moves reciprocally in the self-locking hydraulic cylinder with the help of pressure oil. In order to improve its working effect, there is no sealing ring on the piston to eliminate internal leakage, where the piston rod passes through the self-locking hydraulic cylinder head, due to the existence of the gap, it is easy to produce external leakage phenomenon, and the dust can enter the self-locking hydraulic cylinder through the gap, so the sealing device and dust prevention reason are set. At the same time, in order to eliminate the influence of eccentric load on the work of the piston, all the self-locking hydraulic cylinders must be provided with a considerable length of guide sleeve at the extended end of the piston rod. In addition, in the case of faster piston movement, the phenomenon of mechanical collision between the piston and the self-locking hydraulic cylinder bottom and the self-locking hydraulic cylinder head is serious, so the buffer deceleration should be set at both ends of the self-locking hydraulic cylinder The working medium of the self-locking hydraulic cylinder: because it works at room temperature, the ordinary oil-type hydraulic oil can be selected; self-locking hydraulic cylinder sealing device: The use of Yx sealing ring, polyurethane (PU) and polytetrafluoroethylene (PTFE) materials combined to achieve a good sealing effect; Buffer mechanism of the self-locking hydraulic cylinder: The buffer structure of the self-locking hydraulic cylinder is to prevent the piston from colliding with the self-locking hydraulic cylinder head at the end of the stroke.

The self-locking hydraulic cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure self-locking hydraulic cylinder can use 20 steel pipe, and the high pressure self-locking hydraulic cylinder can use 45 steel pipe.

Answers to some questions about self-locking hydraulic cylinder:

How is the hydraulic cylinder selected in the mechanical design manual?
First of all, it is necessary to meet your work needs, and the second is to meet the structural space of the cylinder and accessories. Three to consider the other parameters of the cylinder.

Why can't the hydraulic cylinder be pulled back after pushing to the limit?
May be long-term use to the limit position, resulting in serious wear caused! The solution is to add the stroke switch or disassemble and add gaskets before and after the piston.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
105国产精品| 亚洲欧美另类综合在线| www.激情五月 五月激情| 秋山祥子人妻一区二区三区| 日日夜夜中文版| 大鸡巴操逼艹视频| 大鸡巴操小逼中午字幕免费看| 天天天天天舔舔舔舔舔| 国产一级夫妻性生活免费大片| 嗯啊哦三级片| 欧美一区二区三区老太婆性生活 | 激情性爱综合韩国大学生| 俺来也五月激情| 欧美日韩日逼逼| 鸡吧操逼视频无遮挡免费| 看日韩操逼片| 插日本美女逼| 男生操女生视频网站在线观看| 中文字幕,视频一区,二区,不卡顿| 被操哭视频在线观看| 大香蕉在线老司机| 超碰免费公开在线观看| 三级片内射网站| 免费看国产夫妻牲生活| 欧美美女逼逼图片| 抽插高潮呻吟视频| 日韩大片网址欧美| 操大逼 视频| 欧美操多人逼视频| 日本一区二区三区暴操老师| 国产婷婷自拍| 亚洲AV无码无一区二区在线| 羞羞答答日本视频| 日逼大全日| 欧美在线观看高清| 亚洲一区二区三区四区操逼小视频| 探花一区| 中文字幕一区二区三区四区乱伦| 丝袜诱惑在线视频一区| 日本性感大扎美女免费操逼视频| 91在线电影中文字幕一区二区三区|