亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo hydraulic cylinder Sold to Oman

Release time:2023-11-17 13:21:23 Hits: Current position: Home > News

This article mainly introduces:

Oman hydraulic cylinder,servo hydraulic cylinder manufacturer,servo hydraulic cylinder

Oman servo hydraulic cylinder

(Oman servo hydraulic cylinder,produced by Hebei Hengyu company)

servo hydraulic cylinder are widely used in Oman,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed servo hydraulic cylinder for customers from Oman.

Introduction to servo hydraulic cylinder:

The assembly work of the servo hydraulic cylinder has a great impact on the quality of the servo hydraulic cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

In order to ensure the service life of the servo hydraulic cylinder, the medium used must not be mixed with impurities and stolen goods, so as to avoid scratching the inner arm of the servo hydraulic cylinder, causing damage to the seal and causing leakage in the servo hydraulic cylinder. It is required that the filtration accuracy of the system is not less than 80μm, the oil pollution is strictly controlled, the hydraulic oil is kept clean, the performance of the hydraulic oil is regularly checked, and the necessary fine filtration or replacement of the new working hydraulic oil is carried out.

Before the servo hydraulic cylinder is removed, the system should be unloaded, the loop pressure is zero, the oil source should be cut off, and the oil port should be blocked after the oil port distribution pipe is loosened.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the servo hydraulic cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

Answers to some questions about servo hydraulic cylinder:

Need a hydraulic cylinder, vertical upward 10 seconds to lift 20 tons of weight up 2 meters, how large cylinder and rod, how much pressure to use the plunger pump and how big?
The first thing to determine the system pressure, let's say 25 mpa, can take into account cost and performance. 1 Cylinder area 20000/250=80 square cm cylinder diameter (80/3.14) squared x2=200 mm 2 cylinder volume 80x200=16000 ml =16 L 3 Required pump flow 16x60/10=96 L/min 4 Power 96x25/55=43 kW 45 kW motor is available.

Why can't the hydraulic cylinder be pulled back after pushing to the limit?
May be long-term use to the limit position, resulting in serious wear caused! The solution is to add the stroke switch or disassemble and add gaskets before and after the piston.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
嗯嗯啊啊啊不要操视频| 视色视色天天天天| 大鸡巴操的骚肉老熟女直叫爽| pacopacomama熟女人妻| 御姐 一区 二区| 国产日韩欧美在线观看免费| 最新日本高清一区二区| 麻豆亚洲爆乳一区二区三区| 怡红院全部视频| 草黑逼| 日韩少妇官网| 美女逼B视频| 亚洲Av专场一区二区三区| 婷婷五月AV网址导航| 18p少妇| 看美女小逼操操| 干少归18p| 欧美大鸡巴插久久| 韩国一区二区三区AV| 黑鸡巴操少妇| 超碰97人妻97| 习近平讲述文物里的文明交融| 91电影黄色| 一把插入女生小穴免费| 成人天堂AV国产| 没日韩伦理片一区二区三区| 嗯,啊,操逼视频| 亚洲曰曰本第一次| 美女喜欢大鸡巴日视频| 污污3D| 九七超碰人妻| 欧美在线免费视频观看| 天堂社区大香蕉| 婷婷五月三级片| 操 日韩美女| 大鸡吧操逼猛烈| 北条麻妃99精品视频| 国产又黄又黑又长| 国产大片免费操逼视频| 骚逼视频免费看,| 亚洲av色国产精品|