亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

push plate cylinder Sold to Peru

Release time:2023-11-17 13:21:22 Hits: Current position: Home > News

This article mainly introduces:

Peru hydraulic cylinder,push plate cylinder manufacturer,push plate cylinder

Peru push plate cylinder

(Peru push plate cylinder,produced by Hengyu Hydraulic Cylinder Factory)

push plate cylinder are widely used in Peru,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed push plate cylinder for customers from Peru.

Introduction to push plate cylinder:

push plate cylinder is the most important part of construction machinery, the traditional processing method is: broaching push plate cylinder block - fine boring push plate cylinder block - grinding push plate cylinder block. The rolling method is: broaching push plate cylinder block - fine boring push plate cylinder block - rolling push plate cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the push plate cylinder block is about 1-2 days, rolling 1 meter of the push plate cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the push plate cylinder increases by 25%. If the push plate cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality push plate cylinders, you must take the rolling production process. After the push plate cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

The difference between the plunger push plate cylinder and the piston push plate cylinder is that the piston in the push plate cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type push plate cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

When the push plate cylinder is disassembled due to oil leakage and other faults, the position of the piston should be moved to any end position of the push plate cylinder by applying liquid pressure. Improper tapping and sudden drop should be avoided during disassembly.

How to determine the working pressure of the push plate cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, push plate cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

Answers to some questions about push plate cylinder:

What is the principle of electric cylinder?
Principle: The electric cylinder converts the rotating motion of the motor into the linear motion of the push rod through the mechanical movement of the lead screw and the lead screw pair. With the closed-loop control characteristic of servo motor, the precise control of thrust, speed and position can be realized easily. Using modern motion control technology, numerical control technology and bus (network) technology, the program and bus (network) control is realized. Because of its easy control and use, it will realize the precision motion control that the cylinder and hydraulic cylinder drive can not achieve. Electric cylinder application field: 1, coordinate manipulator: logistics transmission, automated production line. 2. Wave making machine. 3, parallel mechanism: experimental platform, simulation platform, antenna. 4. Parallel machine tools. 5. Medical equipment: CT, Kamar

What is a hydraulic cylinder assembly?
Assembly, which means aggregate. A series of parts or products, formed to achieve a specific function of the whole, the general term for this system is assembly. The hydraulic cylinder assembly is not a single hydraulic cylinder part, which can be used by connecting the hydraulic hose.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美艳妇精品一区| 欧美一级韩国| 成人老司机在线观看| 水蜜桃18+无套在线看| 中文字幕11页中文字幕11页| 超碰0930| 日韩av网址在线| 干狠狠综合网| 少妇嗷嗷叫在线观看| 亚洲欧美熟妇涩涩| 粉嫩一区二区三区在线看| 骚逼逼无码免费视频| 性交大几把操逼| 中文字幕在线不卡V一二三区| 鸥美日韩一级在线观看| 四十五十路熟女一区二区三区| 2025中文字幕在线一区二区| 日大骚逼免费视频| www.日本av一区二区| 最新高清日本不卡一区| 男子晚上操美女| 人妻中文字幕不卡精品| 亚洲专区人妻互换| 亚洲情侣激情在线| 美女被插视频网页在线| 人妻天天爽夜夜爽2区蜜臀A∨| av亚洲激情| 国际骚货AV| 熟女真一区二区三区SXXHD| 18插逼艹鸡国产区| 泸水县| 看日B做爱视频| 少妇是骚穴淫比| 操操成人AV| 搜索中文字幕第一区| 青青草原午夜影院更狠操| 超碰公开在线97| 国产黑鸡巴| 秋霞一区二三| 日韩高清国产a√| 一区二区麻豆传媒黄片|