亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

Lifting cylinder Sold to Italy

Release time:2023-11-17 13:21:24 Hits: Current position: Home > News

This article mainly introduces:

Italy hydraulic cylinder,Lifting cylinder manufacturer,Lifting cylinder

Italy Lifting cylinder

(Italy Lifting cylinder,produced by Hengyu Group)

Lifting cylinder are widely used in Italy,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed Lifting cylinder for customers from Italy.

Introduction to Lifting cylinder:

If the seal of the Lifting cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the Lifting cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

The quality of the Lifting cylinder can not be ignored in the purchase of the Lifting cylinder. The Lifting cylinder is the main component of the Lifting cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Lifting cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of Lifting cylinder is deep hole processing, which has always troubled the processing personnel.

The internal leakage of the Lifting cylinder should be prevented when the Lifting cylinder is used. The internal leakage of Lifting cylinder includes the leakage caused by excessive wear of Lifting cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

Answers to some questions about Lifting cylinder:

PLC+ inverter + motor + pump + solenoid valve + cylinder combination, can control the accuracy of cylinder position?
In the case of extremely high accuracy requirements, you can not, please consider a few problems: 1, hydraulic oil can be compressed, it is elastic like a spring. Therefore, in the general hydraulic servo system, the valve control is far more accurate than the pump control. Because the valve can be installed very close to the hydraulic cylinder, or even installed on the hydraulic cylinder, but the pump must go through the tubing and then into the hydraulic cylinder, there is a long distance, which greatly reduces the rigidity of the system and increases the difficulty of control. 2, the quantitative pump is first of all leaking, and there is 10%-20% flow pulsation. Secondly, and more unfortunately, the leakage of the pump is related to the pressure and is non-linear.

What is the clearance between the cylinder and the piston?
The gap between the cylinder and the piston in the radius is generally 40 wires, that is, about 0.4mm, and the gap of the cylinder with different diameters will be slightly different. Generally, the inner diameter of the cylinder is larger than the outer diameter of the piston, so as to prevent the friction between the outer surface and the inner surface of the cylinder during the operation of the piston. In order to ensure that the cylinder has a rod cavity and a rodless cavity seal, a sealing device, that is, a sealing ring, is installed on the outer surface of the piston. The sealing ring form is not exactly the same, the O-type sealing ring is generally used under low pressure, and the lip sealing ring is used under high pressure. At the same time, the outer circle of the piston is also equipped with a dust ring and a wear ring. As long as the cylinder seal fails, all the internal seals should be replaced.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
18禁网站在线免费观看| 欧美午夜男人天堂| 欧美日韩欧美性生活视频| 一区二区www不卡视频| 亚洲媚药系列中文字幕| 中文字幕手机一区二区| 逼中鸡吧视频| 人妻少妇三区| 抽插AV黄页| 新红楼AV在线| 红桃视频综合啪啪啪一区二区| 超碰在线97视4| 韩国深夜三级成人片| 桃国产精品一区| 在线欧美视频有B吗| 大鸡鸡草小逼| 白丝被艹视频| 三上悠亚中文字幕一区二区三区 | 日韩极品少妇, | 日韩美女裸體操逼視頻播放器| 免费看理论永久一区| 亚洲精品九色熟女| 激情人妻欧美色图| 收看日本十七岁的免费的黄色录像| 操美女小鸡鸡欧美网站| 亚洲 欧洲 日韩AV| 操你小骚逼| 性插免费网页| 久操16p| 污亚久| 骚 成人在线| 亚洲尤物美女午夜啪啪视频| 果冻麻豆操骚逼视频| 18禁美女无遮挡免费| 极品少妇自慰在线| 国产大鸡吧干女人逼| 免费的操逼视频白丝| 五十六十日本老熟妇| 中出性感美少妇| 骚笔无码| 欧美日小穴|