亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steering cylinder Sold to Belarus

Release time:2023-11-13 11:19:51 Hits: Current position: Home > News

This article mainly introduces:

Belarus hydraulic cylinder,steering cylinder manufacturer,steering cylinder

Belarus steering cylinder

(Belarus steering cylinder,produced by Hengyu Hydraulic Co., Ltd)

steering cylinder are widely used in Belarus,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed steering cylinder for customers from Belarus.

Introduction to steering cylinder:

steering cylinder diameter, rod diameter, stroke determination: Choose national standards or other standards steering cylinder, avoid the selection of non-standard size, otherwise the difficulty of processing and manufacturing costs will be increased. The length of the steering cylinder guide is determined by the length of the stroke. Check the strength of steering cylinder, piston rod, screw, etc. according to the working pressure or load. At the same time, working pressure, ambient temperature, working medium and running speed are also the key to selecting seals.

steering cylinder installation precautions: Before installing the steering cylinder into the system, the parameters on the steering cylinder label should be compared with the parameters when ordering. The base of the steering cylinder must have sufficient stiffness, otherwise the steering cylinder will bend upward into a bow when pressurized, so that the piston rod will bend.

When the steering cylinder is installed, the piston and the steering cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the steering cylinder head boss is easy to cause scars when it hits the inner surface of the steering cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized steering cylinders, only careful and careful operation can be avoided.

steering cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the steering cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

Answers to some questions about steering cylinder:

How is the cylinder of hydraulic cylinder processed?
As the main parts of hydraulic cylinder, mining single pillar, hydraulic support, gun barrel and other products, its processing quality directly affects the life and reliability of the whole product. Cylinder processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of cylinder is deep hole processing, which has always troubled the processing personnel. Due to the residual compressive stress on the surface of the surface layer, the rolling machining is helpful to seal the small cracks on the surface and prevent the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the cylinder can be improved.

What causes hydraulic cylinder oil leakage?
1. Internal leakage (1) The wear ring on the piston is seriously worn, leading to friction between the piston and the cylinder liner, and finally strain the cylinder liner, piston and seal; 2) Seal long-term use failure, piston seal (mostly U, V, Y ring, etc.) aging; 3) The hydraulic oil is dirty, and a large number of impurities enter the cylinder and wear the piston seal to bad; 2. External leakage 1) cylinder inlet and outlet tubing joint cracking; (This I see in the actual work is still more) 2) The piston rod extension end with the piston rod seal damage, mostly due to the piston cylinder is caused by hair, but also caused by aging; 3) The seal between the extended end of the piston rod and the liner is damaged.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
澎湖县| 亚洲色图第一区第二区第三区| 在线观看亚洲骚av| www操逼| 欧美激情极品日韩| 中字无码中出在线观看| 亚洲天堂午夜场| 国产免费一区二区三区三州老师视频 | 久久久国产精品绝色影视| 带亚洲成人AV一卡二卡| 国产一区二区三区三州久久| 裸体美女视频久久| 欧美啪啪啪熟妻| avtt天天干| 铁力市| 久久激情性爱| 鸡巴操免费视频| 欧日韩免费视频| 一区二区观看伦理| 日韩和欧美的一区二区区| 欧美在线一.| 日韩女人操逼网| 色五日婷婷老师激情| 嗯啊家访操逼视频| 黑人日韩人妻黄色影片| 大香蕉超视频| 精品熟女时时| 定南县| 午夜啪啪福利视频| 91中文字幕大屁股| 大鸡巴操,小骚逼免费视频| 草b美女| 欧美美女吃鸡巴操逼| 大粗鸡巴操亚洲夫妻视频| 性生活试看视频久久久久久中文字幕亚洲 | 日韩五十路女人激情视频| 欧美360av免费播放| 欧美黑人大鸡鸡| 性感的波多野结衣视频在线播放| 欧美熟女在线线| 亚洲强伦老女人一区二区|