亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

rack cylinder Sold to Mexico

Release time:2023-11-13 11:19:51 Hits: Current position: Home > News

This article mainly introduces:

Mexico hydraulic cylinder,rack cylinder manufacturer,rack cylinder

Mexico rack cylinder

(Mexico rack cylinder,produced by Hebei Hengyu company)

rack cylinder are widely used in Mexico,because of high work efficiency,high work efficiency,clever hydraulic energy conversion.So our company has designed rack cylinder for customers from Mexico.

Introduction to rack cylinder:

If air enters the hydraulic system, the rack cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

The cavitation of the rack cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the rack cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

The pressure of the sliding surface of the rack cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the rack cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

rack cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

Answers to some questions about rack cylinder:

How to disassemble injection molding machine injection cylinder?
If it is not repaired for a long time, it is recommended to open both ends, comprehensively check the oil seal and piston ring inside, this is not much difficulty, pay attention to not install reverse when changing the oil seal, some piston rings are steel rings are rubber rings, and several interfaces of steel rings are not in the same position; Rubber ring pay attention not to install reverse; Be careful not to damage the oil seal when installing, otherwise it will soon leak oil.

Servo cylinder control principle
The electro-hydraulic pulse servo cylinder is composed of a stepper motor, a three-position four-way servo valve, a mechanical feedback device (a wire carrier) and an oil lever. When the stepper motor gets a pulse signal, its output shaft rotates 1.5 or 3 degrees, the servo valve spool drives the wire to rotate at the same time, the valve spool moves and opens the reversing cylinder to output pressure oil, the piston moves and drives the lead screw to reverse rotate the valve spool back to the original position, and the servo valve stops output pressure oil in the center. At this time, the cylinder moves 0.1 or 0.2mm stroke, and the displacement and speed of the cylinder travel are determined according to the given value of the electrical pulse.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
啊啊啊舒服视频免费观看| 美女被男人桶爽的嗷嗷叫| 殴美大机吧操美女大逼视频| 日本又黄又骚的视频| 国产一区二区啪啪| 裸体久久一区二区三区| 欧美破处日韩| 啊..啊..好舒服网站| 国产吧国产吧av| 日韩欧美风情视频| 老女人乱婬一区二区三区| 欧美一区二区三区三州视频| 嗯额嗯啊嗯啊视频在线观看| 插逼视频资源| 国产麻豆吊| 中文字幕石原莉奈| 大鸡巴在日逼视频| 亚洲AV日韩AV一道本香蕉| 专干老熟女A片无码国产| 日韩欧美成人录像在线免费| 大长屌日逼视频| 国产av福利久久精品| 久艹性生活视频免费看| av在线亚洲一区| 天天日天天操天天www| 国产欧美日韩视频视频在线| 性爱视频 午夜| 美女喷水视频网站| 欧美少妇自慰21p| 美日韩操B小视频| 良家白嫩AV在线| 韩国日本人妻三级片网站| 老司机五月天久久| 台湾娱乐性综合中文网22| nanrenlurencaobi| 大鸡巴插熟妇| 国产日韩欧美毛片在线| 国产精五月天性爱| 五月 涩婷| 尹人醉大香蕉| www日日本本道高清色艹|