亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailboard balance cylinder Sold to Belarus

Release time:2023-11-13 11:19:52 Hits: Current position: Home > News

This article mainly introduces:

Belarus hydraulic cylinder,tailboard balance cylinder manufacturer,tailboard balance cylinder

Belarus tailboard balance cylinder

(Belarus tailboard balance cylinder,produced by Hengyu Hydraulic Co., Ltd)

tailboard balance cylinder are widely used in Belarus,because of long service life,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed tailboard balance cylinder for customers from Belarus.

Introduction to tailboard balance cylinder:

If the seal of the tailboard balance cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and tailboard balance cylinder, and the phenomenon of "pulling the tailboard balance cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

When the tailboard balance cylinder is customized, if there are high requirements for the quality of the tailboard balance cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the tailboard balance cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the tailboard balance cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

tailboard balance cylinder can not drive the load troubleshooting: oil pressure is too low. tailboard balance cylinder selection specifications are too small. Leakage in tailboard balance cylinder or associated hydraulic system element.

tailboard balance cylinder is the most important part of construction machinery, the traditional processing method is: broaching tailboard balance cylinder block - fine boring tailboard balance cylinder block - grinding tailboard balance cylinder block. The rolling method is: broaching tailboard balance cylinder block - fine boring tailboard balance cylinder block - rolling tailboard balance cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the tailboard balance cylinder block is about 1-2 days, rolling 1 meter of the tailboard balance cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the tailboard balance cylinder increases by 25%. If the tailboard balance cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality tailboard balance cylinders, you must take the rolling production process. After the tailboard balance cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

Answers to some questions about tailboard balance cylinder:

When does the cylinder rotate?
The piston rod inside the multistage plunger cylinder can be rotated, and it will rotate when it is subjected to tangential force.

What are the causes of hydraulic cylinder oil leakage?
First, between the piston rod and the guide sleeve: 1, the cylinder force is not good, there is a radial force between the piston rod and the guide sleeve there is a partial load, so that the oil seal is worn early, causing oil leakage. 2. The ambient temperature of the piston rod is high, especially radiant heat, and the oil seal aging is fast. 3. Whether the oil seal is selected correctly; Check whether the oil seal is damaged during installation. 4, guide sleeve and piston rod matching tolerance is correct. Second, between guide sleeve and cylinder: 1. Whether the O-ring on the guide sleeve is installed correctly, pay special attention to the O-ring can not "roll", especially some O-rings are die-pressed with a die-closing line. Third, common problems: 1, guide sleeve, cylinder, piston rod concentricity is poor. Fit tolerance is correct.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩大屁股在线一区二区| 肛高清无码在线播放| 东北老骚逼AV c com| 欧美日韩黑屌| 深夜福利日韩一区| 大黑逼在线播放| 中文有码二页| 亚洲精品10p| 美女黄视频图片| 看精品大鸡巴操美女逼视频 | 天天美女的大骚逼| 久久少妇厕所偷拍| 黄色探花在线观看| 在线日本有码视频| 一道一本综合精品久久中文字幕| 韩国老女人乱伦| 按摩美女操机巴视频| 色五月婷主播撸一撸| 高清一区二区卡三区四区日本| 亚洲码视频| 中国美女厕所操逼| 亚洲一区 欧美 蜜臀 semiao| 亚洲色图春色| 操四川BB娇小BB痒BB| 国产一级精品黃色象帶| 福利网站干| 熟妇大鸡巴操爽了| 七七久久亚洲| 日韩欧美成人录像在线免费| 欧美日韩国产日韩视频| 福利大香蕉视频在线观看| 青青草绿色在线| 石原莉奈亚洲第一| 女子在线看片国产| 骚逼AV电影院| 91国产这里只有精品蜜| 欧美日韩国国产无码一级视频| 午夜福利精品h| 在线 大屁股 后入| 铁力市| 欧羌日韩免费大香蕉|