亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailboard balance cylinder Sold to Qatar

Release time:2023-11-10 08:35:27 Hits: Current position: Home > News

This article mainly introduces:

Qatar hydraulic cylinder,tailboard balance cylinder manufacturer,tailboard balance cylinder

Qatar tailboard balance cylinder

(Qatar tailboard balance cylinder,produced by Hengyu Hydraulic Co., Ltd)

tailboard balance cylinder are widely used in Qatar,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed tailboard balance cylinder for customers from Qatar.

Introduction to tailboard balance cylinder:

Before purchasing the tailboard balance cylinder, it is necessary to master the original information and design basis, mainly including: the use and working conditions of the machine; The structural characteristics, load conditions, stroke size and operation requirements of the working mechanism; The selected working pressure and flow of the hydraulic system; The reality of materials, fittings and processes; Relevant national standards and technical specifications, etc.

Piston tailboard balance cylinder is widely used in hydraulic transmission. When the tailboard balance cylinder works, it mainly delivers hydraulic oil alternately to both sides of the piston in the tailboard balance cylinder, and uses the pressure difference of hydraulic oil on both sides of the piston to realize the reciprocating movement of the piston. If you want to speed up the forward speed of the piston, the return oil in the tailboard balance cylinder can be controlled by the valve and directly input into the inlet pipe to participate in the work of the piston to achieve rapid movement of the piston, but the thrust of the piston is reduced much.

When installing the tailboard balance cylinder, the axial ends of the tailboard balance cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the tailboard balance cylinder, there is axial expansion. If the two ends of the tailboard balance cylinder are fixed, all parts of the tailboard balance cylinder will be deformed. When disassembling the tailboard balance cylinder, it is strictly forbidden to hammer the tailboard balance cylinder and the piston surface, such as the tailboard balance cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

When the tailboard balance cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

Answers to some questions about tailboard balance cylinder:

How to deal with oil cylinder leakage?
The causes of oil leakage and treatment methods are as follows: (1) The spool is stuck or the valve hole is blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check valve body for wear. (2) The piston rod and cylinder are stuck or the hydraulic cylinder is blocked. At this time, no matter how to operate, the hydraulic cylinder does not move or moves very little. At this time, it should be checked whether the piston and piston rod seal is too tight, whether it enters the dirt and colloid precipitate: whether the shaft line of the piston rod and the cylinder is in alignment, and whether the wearing parts and seals are invalid.

How to judge the leakage in the cylinder?
Common judgment method: In the production site, people make full use of watching, listening, smelling, touching and other sensory ways, by observing that the cylinder can not move or delay the action or feel the oil temperature change, vibration and noise, etc., and then judge whether the cylinder has internal leakage according to experience. Another method commonly used in the field is to extend the cylinder in place to ensure that the cylinder does not have any load and will not retract (to prevent the cylinder from internal leakage accidents), turn off the machine, and then remove the tubing with the rod cavity, and then press the switch that pulls out the cylinder (do not press the wrong switch). If the oil nozzle with the rod cavity drains the cylinder internally, If there's no oil coming out, you have to think about something else going wrong.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
一区有码免费视频| 和国产精品大鸡巴进进出出| 福利手机小视频网址| 高清一区二区三区四区五区精品| 亚洲少妇制服| 操啊操逼| 88av在线视频强上| 操逼网站大鸡巴| 操嗯啊骚靠流水逼| 日韩久久久久免费视频| 日韩乱性视频网| 麻豆女优人体艺术视频| 日韩中文一文| 欧美日韩干B| 美女的下面被插网站| 美女被桶爽的视频| 女生被男生操的好爽免费视频网站| 久九热九| 老太婆熟女pp一区二区| 欧美美女大黄操逼| 国产微拍福利一区二区在线观看| 乱伦老女人网| 插美女动态| 操B,干B,赤B,| 麻豆精品一二三艹| 日韩欲求不满人妻一区二区 | 江华| 肏逼内射视频| 国产精品激情福利视频| 中文字幕一区二区三区四区五区电影| 超碰国产御姐在线| 欧美色图 啪啪啪视频| 91被插视频| 欧洲少妇粗大19P| 97熟女网| 亚洲综合成人婷婷五月网址| 黄浦区| 超碰在线观看综合日本欧美| 欧美日韩一级片免费观看| 得得干在线视频播放| 大鸡吧日少妇|