亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

supporting cylinder Sold to Cote d 'Ivoire

Release time:2023-11-10 08:35:26 Hits: Current position: Home > News

This article mainly introduces:

Cote d 'Ivoire hydraulic cylinder,supporting cylinder manufacturer,supporting cylinder

Cote d 'Ivoire supporting cylinder

(Cote d 'Ivoire supporting cylinder,produced by Hengyu Hydraulic Co., Ltd)

supporting cylinder are widely used in Cote d 'Ivoire,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed supporting cylinder for customers from Cote d 'Ivoire.

Introduction to supporting cylinder:

The material, shape and compression of the supporting cylinder seal have a great impact on the service life and work efficiency of the supporting cylinder. In addition to requiring a reliable seal, it should also have a long service life and less friction loss. At present, there are many seal manufacturers in the country, and it is also crucial to choose high-quality seals with reliable and stable quality.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the supporting cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

In order to ensure the service life of the supporting cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

supporting cylinder use should try to avoid sealing belt into the supporting cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the supporting cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the supporting cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

Answers to some questions about supporting cylinder:

What do cylinder internal leakage and external leakage mean?
Internal leakage means that the piston seal in the cylinder is not strict, there is a leak between the two chambers of the cylinder, the oil is still in the cylinder, and the external leakage is that the oil leaks to the outside of the cylinder.

What are the causes of hydraulic cylinder oil leakage?
First, between the piston rod and the guide sleeve: 1, the cylinder force is not good, there is a radial force between the piston rod and the guide sleeve there is a partial load, so that the oil seal is worn early, causing oil leakage. 2. The ambient temperature of the piston rod is high, especially radiant heat, and the oil seal aging is fast. 3. Whether the oil seal is selected correctly; Check whether the oil seal is damaged during installation. 4, guide sleeve and piston rod matching tolerance is correct. Second, between guide sleeve and cylinder: 1. Whether the O-ring on the guide sleeve is installed correctly, pay special attention to the O-ring can not "roll", especially some O-rings are die-pressed with a die-closing line. Third, common problems: 1, guide sleeve, cylinder, piston rod concentricity is poor. Fit tolerance is correct.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
婷婷依依久久五月| 国产美女网站大全免费观看视频| 亚洲色图自拍偷拍二区| 女同啪一区| 国产+欧美+熟女| 久久久精品国产丝袜正小| 亚洲青青草视频| 日韩综合第91页| 91精品亚洲一区| 亚洲av.一二区| 亚洲bv一区二区三区9| 视频在线17cn老司机| 国产熟妇色在线观看一下| 手机看国产黄片| 欧美日韩不卡线观看| 亚洲男人的天堂AVXXⅩX太久| 成人一区二区不卡欧美| 18禁在线一区| 福利视频网战| 人妻激情麻豆综合| 隆德县| 囯产自拍亚洲精品| 美国另类操b视| 老湿午夜在线观看| 在线素人少妇| 美女后入91| 熟女夜生活东京热| 欧美偷拍自拍色图网| 大香蕉日本最新午夜播放| 自拍 偷拍 福利论坛| 久久精品打炮| 亚洲中文在线三十三区| 抽插女生小穴的视频| 99热这里只有精品最新2| xxx鸡巴好大操网站| 一区二区久骚| 亚洲av电影1区2区| 91powered一二三区| 超碰亚洲国家熟女天天爽| 亚洲成人女同一区| 人人乐人人澡人人妻一二三区|