亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

vehicle hydraulic cylinder Sold to Indonesia

Release time:2023-11-10 08:34:47 Hits: Current position: Home > News

This article mainly introduces:

Indonesia hydraulic cylinder,vehicle hydraulic cylinder manufacturer,vehicle hydraulic cylinder

Indonesia vehicle hydraulic cylinder

(Indonesia vehicle hydraulic cylinder,produced by Hengyu Group)

vehicle hydraulic cylinder are widely used in Indonesia,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed vehicle hydraulic cylinder for customers from Indonesia.

Introduction to vehicle hydraulic cylinder:

The vehicle hydraulic cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the vehicle hydraulic cylinder should pay attention to: the operation should be as far away from the vehicle hydraulic cylinder as possible, to avoid falling objects, knocking, rubbing the vehicle hydraulic cylinder coating. When cleaning the vehicle hydraulic cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the vehicle hydraulic cylinder when the oil temperature exceeds 70 ° C.

Most of the failure of the vehicle hydraulic cylinder is because there is a foreign body in the vehicle hydraulic cylinder into the failure of the vehicle hydraulic cylinder, the most problematic is that it is difficult to determine when the foreign body is into the vehicle hydraulic cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

vehicle hydraulic cylinder spool stuck or valve hole blocked How to solve: When the flow valve or direction valve spool stuck or valve hole blocked, the vehicle hydraulic cylinder prone to misoperation or action failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium.

When the initial action of the vehicle hydraulic cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the vehicle hydraulic cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

Answers to some questions about vehicle hydraulic cylinder:

How to take out the diaphragm of hydraulic cylinder? The septum ring is also known as the septum sleeve, when the cylinder is too long, and does not need too much travel, add the septum sleeve, limit the stroke of the hydraulic cylinder, set on the piston rod, only contact with the guide sleeve and piston, do not cooperate with the cylinder, limit the stroke, take out the difficulty is different, need to have such a professional tool, before taking out to consult the manufacturer.

Two cylinders in parallel, how to solve the synchronization problem?
The following methods can be used to achieve parallel cylinder synchronization: 1, rigid mechanical synchronization. 2. The throttle valve or speed regulating valve is used in the circuit to adjust the synchronization. 3, the two cylinders use independent quantitative pump oil supply to achieve synchronization. 4. Synchronous motor is used in the loop to realize cylinder synchronization. 5, using the position sensor to measure the stroke position and control the cylinder synchronization through the electrical system.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美一区二区三区爱爱视频| 国产剧情巨作无码传媒av在线| 国产又猛又粗又爽视频| 北岛玲无码人妻在线| 日本久久美女网| 日韩怡红楼| 天天干,天天看,天天日| 有大求日逼视频| 男人天堂一区av| 日逼逼啊啊AV| 男女视频吃鸡巴| 大香蕉96日韩久在线| 内射极品在线| 日韩美女做爱视频| 日本伊人自拍偷拍| 白嫩小穴视频在线免费观看| 美女扒开裤子让男生捅视频免费观看| 91人人操人人操| 不卡性生活片| 情侣超碰在线播放| 欧美粗大免费在线| 亚洲精品啊啊啊操好舒服| 五月婷婷一| 午夜免费AV电影| 日本色情淫乱五月天一区| 熟女偷拍网| 日本久久久精品视频| 国产女精品| 亚洲有码中文字幕av| 欧美大逼精品操老太太大逼| 熟女出水一区二区三区| 操我吧av| 婷婷久久综合九色综合88| 大鸡巴操美女在线观看网站| 亚洲 丝袜 人妻| 超超超超碰国产| 日本大香焦巨乳在| 美女视频无遮挡网站| 成人韩国三级国产三级| 三上悠亚AV一区二| 欧美色综合韩国欧美|