亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

yg series hydraulic cylinder Sold to New Zealand

Release time:2023-11-10 08:34:47 Hits: Current position: Home > News

This article mainly introduces:

New Zealand hydraulic cylinder,yg series hydraulic cylinder manufacturer,yg series hydraulic cylinder

New Zealand yg series hydraulic cylinder

(New Zealand yg series hydraulic cylinder,produced by Hebei Hengyu company)

yg series hydraulic cylinder are widely used in New Zealand,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed yg series hydraulic cylinder for customers from New Zealand.

Introduction to yg series hydraulic cylinder:

If the piston rod and yg series hydraulic cylinder are stuck or the yg series hydraulic cylinder is blocked, at this time, no matter how to operate, the yg series hydraulic cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the yg series hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

The scar on the sliding surface of the yg series hydraulic cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the yg series hydraulic cylinder wall. Therefore, before installation, these scars must be fully repaired.

Causes and countermeasures of oil yg series hydraulic cylinder leakage: Cast iron ring seal allows a certain degree of internal leakage. The impurities in the yg series hydraulic cylinder will lead to premature wear of the piston seal, replace the piston seal; If the yg series hydraulic cylinder is visibly scarred, the yg series hydraulic cylinder must be replaced. It can be pressurized at one end of the yg series hydraulic cylinder and opened at the other end of the oil port to observe whether there is obvious internal leakage at the end of the oil port. Most yg series hydraulic cylinder piston drift may not come from the yg series hydraulic cylinder, the above method to determine the yg series hydraulic cylinder without internal leakage is helpful to determine the problem of the hydraulic system related components.

The meaning of the yg series hydraulic cylinder model marked by the yg series hydraulic cylinder manufacturer: for example, 160/100-1150, its meaning: from a professional point of view, 160 refers to the yg series hydraulic cylinder diameter, which is 160mm, and the 100 behind refers to the rod diameter, which is 100mm. The 1150 refers to the yg series hydraulic cylinder stroke, which is 1150mm. Therefore, on this point, we should have a correct understanding and can not make mistakes.

Answers to some questions about yg series hydraulic cylinder:

What are the requirements for hydraulic cylinder assembly? ① The installation of the cylinder should be solid and reliable. In order to prevent the influence of thermal expansion, in the case of large stroke and hot working conditions, one end of the cylinder must be kept floating.② pipe connection shall not be relaxed.③ The mounting surface of the hydraulic cylinder and the sliding surface of the piston rod should maintain sufficient parallelism and perpendicality.④ The central axis of the moving cylinder should be concentric with the center line of the load force, otherwise it will cause lateral force, which is easy to wear the seal And piston damage. The greater the distance between the supporting points of the piston rod, the smaller its wear. For the hydraulic cylinder of the moving object, the installation should keep the cylinder parallel with the moving object, and the degree of non-parallelism is generally not greater than 0.05mm/m. ⑤The sealing ring should not be installed too tightly, especially the U-shaped sealing ring.

The two cylinders of the bending machine are out of sync?
Check whether the sliding slide is worn, adjust its tightness, so that both sides are consistent, check whether the two cylinder tubing is connected, tighten the flow valve, pressure, let the cylinder air discharge.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
波多野结衣51视频| 日韩一区在线免费视频| 后入乳液爆操91| 免费亚洲婷婷五月| 超碰成人在线分享| 加勒比无码人妻东京热| 日韩无码一区二区中文字幕| 美女BB被操| 射骚逼特级黄片亚洲无码| 无套内内射蜜桃臀| 欧美老妇人xxxx.久久婷综合五| 中文字幕一区二区| 被大鸡巴插到高潮高清视频在线观看 | 海盐县| 色五月综合婷婷| 操一艹日一日| 逼逼逼AV| 亚洲日韩AV在线不卡一区二区三区| 95熟妇精品在线视频| 我要看三区女人插逼| 男人狠狠干视频| 亚洲国产一区二区逼逼大鸡巴| 鸡吧好大好像操b视频| 中文字mu一二三四| 秋霞午夜AV一区二区三区| 欧美美女被操作| 成人区人妻精品一区二区蜜柚| 国产精品福利视频一区| 肛交亚洲无码| 日韩性av嗯哦| 淫妻熟女偷拍视频| 大肉棒进入小穴穴电影网站| 操大B骚妇视频在线观看-一| 激情五月亚洲男人天堂综合网| 欧美色图亚洲色图自拍偷拍| 大奶美女操B国产| 中文有碼 在線觀看| 日本有码 在线播放| 小穴操爽视频| 一夲道不卡网一二三区| 美女的操逼|