亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

flange type cylinder Sold to Australia

Release time:2023-11-12 15:33:23 Hits: Current position: Home > News

This article mainly introduces:

Australia hydraulic cylinder,flange type cylinder manufacturer,flange type cylinder

Australia flange type cylinder

(Australia flange type cylinder,produced by Hengyu Group)

flange type cylinder are widely used in Australia,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed flange type cylinder for customers from Australia.

Introduction to flange type cylinder:

The piston rod and guide sleeve function of the flange type cylinder is crucial: the relative motion pair between the piston rod and the guide sleeve is the main factor causing external leakage, if the chrome layer on the surface of the piston rod is spalling or producing longitudinal tensile marks due to wear, it will directly lead to the failure of the seal.

flange type cylinder use should try to avoid sealing belt into the flange type cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the flange type cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the flange type cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

The piston seal of the flange type cylinder is the main element to prevent leakage in the flange type cylinder. For the lip seal, it should focus on checking whether the lip edge is bruised and worn, and for the combination seal, it should focus on checking the wear of the sealing surface, and then determine whether the seal can be used. In addition, it is necessary to check whether the static seal between the piston and the piston rod is crushed. The piston rod seal should focus on checking the wear of the seals and supporting rings.

The internal leakage of the flange type cylinder should be prevented when the flange type cylinder is used. The internal leakage of flange type cylinder includes the leakage caused by excessive wear of flange type cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

Answers to some questions about flange type cylinder:

How to judge the leakage in the cylinder?
Common judgment method: In the production site, people make full use of watching, listening, smelling, touching and other sensory ways, by observing that the cylinder can not move or delay the action or feel the oil temperature change, vibration and noise, etc., and then judge whether the cylinder has internal leakage according to experience. Another method commonly used in the field is to extend the cylinder in place to ensure that the cylinder does not have any load and will not retract (to prevent the cylinder from internal leakage accidents), turn off the machine, and then remove the tubing with the rod cavity, and then press the switch that pulls out the cylinder (do not press the wrong switch). If the oil nozzle with the rod cavity drains the cylinder internally, If there's no oil coming out, you have to think about something else going wrong.

How to judge the failure of forklift hydraulic cylinder?
The common faults of the hydraulic cylinder of forklift truck are mainly crawling, insufficient thrust, working speed decline or even stop. Generally, crawling occurs at low speed. The main reason is that the air stored in the cylinder is not cleared. In addition, excessive or uneven mechanical friction can also cause crawling. Such as the piston and the piston rod different heart, the piston rod full length or local bending, the cylinder hole straightness is poor, the cylinder is drum shaped or has a large taper, the cylinder thin finish decline or produce hair, the cylinder installation accuracy is out of whack, the piston rod nuts at both ends of the screw too tight to make its concentricity is poor, the oil seal screw too tight friction is too large, will cause crawling.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女搞b视频在线观看| 亚洲欧洲韩日午夜一线一品| 甘泉县| 国产传媒欧美日韩成人大片| 0P亚洲精品| 日韩欧美偷拍一区| 哦,嗯嗯,好舒服视频| 黄色激情自拍偷拍视频| 爽嫩 水 啊 视频 在线| 欧美一二三视频区| 日韩美女国产女主播| 国产视频导航| 欧美色老太太一区二区| 国产骚逼内射视频| jiuyaoai9999| 插入小穴抽插视频| 日韩欧美扒开| 亚洲无码av一区二区三区!| 成人动漫午夜Av| 五十路交尾无吗毛茸茸在线| 欧美精品逼逼逼逼逼| 熟女被干视频| 日韩偷人妻| 美女被操逼图片| 日韩地址一二三四区| 婷婷 综合 色| 国产成人自拍三级片在线观看| 男生桶女生鸡鸡的视频在线| 91超级彭在线| 国产精品美人 | 东北老骚妇操b视频| 日韩欧美五十路| 欧美日韩高清无| 嗯 啊啊啊 继续 啊啊啊 艹我视频 | 台湾佬中文在线播放2222v| 中文字幕在线观看juy| 久久精品伊人老司机蜜桃| 抽插视频不用下载直接看| 干亚洲美女小穴的视频| 东京热无码中出特辑| 关于女生被插入内射的视频网站 |