亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tension cylinder Sold to Sweden

Release time:2023-11-07 17:47:59 Hits: Current position: Home > News

This article mainly introduces:

Sweden hydraulic cylinder,tension cylinder manufacturer,tension cylinder

Sweden tension cylinder

(Sweden tension cylinder,produced by Hengyu Hydraulic Cylinder Factory)

tension cylinder are widely used in Sweden,because of no need for deceleration device,smooth movement,long service life.So our company has designed tension cylinder for customers from Sweden.

Introduction to tension cylinder:

When the tension cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

When the tension cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the tension cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the tension cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the tension cylinder can meet the requirements by grinding. However, the life and reliability of this repair tension cylinder are not high.

How to repair the tension cylinder body when it is damaged: When the tension cylinder has trace deformation and shallow tensile marks, the tension cylinder is repaired by strong honing process. The heavy honing process can repair tension cylinders up to 2.5 times out of tolerance than the original tolerance. It honed the parts with excessive size or shape error through a powerful honing machine, so that the overall size, shape tolerance and roughness of the tension cylinder can meet the technical requirements.

The repair method of the tension cylinder: the repair of the tension cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

Answers to some questions about tension cylinder:

How to calculate the tonnage of hydraulic cylinder? The tonnage of the cylinder refers to the output force of the cylinder under rated working pressure: 1, for single rod piston hydraulic cylinder, it can be calculated by the area of the circle corresponding to the inner diameter of the cylinder A (square centimeter), and the rated working pressure of the system p (mpa), the value is equal to 10pA kg force, and the ton is 0.01pA. 2, for the double rod piston hydraulic cylinder, with A(square centimeter) to indicate the cylinder cylinder diameter and piston rod outer diameter defined by the ring area, with p (mpa) to indicate the rated working pressure of the system, the output force of the cylinder is 0.01pA ton force.

Why do two hydraulic cylinders lift out of sync?
There may be several situations (do not know the result of the equipment, may not be accurate) 1, whether the slow one is worn 2, whether there is air in the slow cylinder 3, if the two cylinders are supplied by the same oil port, whether the slow joint is blocked (some processing residue will reach a certain oil port under a certain coincidence condition, This situation will not happen if it is not necessarily good before) 4, the oil seal in the slow cylinder leaks, causing the feed oil to leak from the return oil end. Point 4 is most likely because it is invisible and a technical failure. If it is a dual oil feed (separate oil feed), it is also necessary to check the oil supply system and the oil return system (valve type).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产 良家 亚洲 熟女| 欧美国产综合网| 日韩一区二区三区大骚逼| 美女乳头视频一区二区| 久久b婷婷五月w| 亚洲人妻精品91| 中文解说美女操逼视屏| 操B免费看| 日本精品成人一区二区三区| 自拍 偷拍 福利论坛| 正阳县| 老女人淫乱视频网| 怡红院一区二区强奸| 日本大鸡吧插骚逼视频| 中文字幕乱码一区二区在线短看| 六月婷婷五月欧美| 操小嫩逼一二三区视频| 91午夜诱惑| 亚洲热伦韩日线在线播放| 色色婷婷网| 色鬼大鸡巴免费视频| 好屌妞偷偷操天堂| AV网址大全一区二区三区| 操日本美女操逼动漫| 美女站着让别人捅| 中文字幕一区二区三区不| 婷婷麻豆精品一区| 裸体美女日逼逼逼| 东北操逼高清| 码高清AV一区二区| 操美女久久| 加勒比Av色| 啊啊好大好爽在线看| 美女啪啪午夜| 日B艹B视频| 天天综合亚洲色| 欧美人妻吃大鸡巴| 人人抽插视频| 美女秒拍福利视频| 日本 黑丝 交| 国产成人丰满熟女干B视频|