亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

large bore cylinder Sold to Kenya

Release time:2023-11-12 15:30:00 Hits: Current position: Home > News

This article mainly introduces:

Kenya hydraulic cylinder,large bore cylinder manufacturer,large bore cylinder

Kenya large bore cylinder

(Kenya large bore cylinder,produced by Hebei Hengyu company)

large bore cylinder are widely used in Kenya,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed large bore cylinder for customers from Kenya.

Introduction to large bore cylinder:

When the large bore cylinder needs to be stored for a period of time, please follow the recommended methods: The large bore cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the large bore cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil large bore cylinder should not be in direct contact with water vapor for a long time. The large bore cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the large bore cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the large bore cylinder Before working, the large bore cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the large bore cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

When the initial action of the large bore cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the large bore cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

In the process of using the large bore cylinder, sometimes such a problem will occur, the large bore cylinder can not act immediately after the instruction of the large bore cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil large bore cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular large bore cylinder action. Troubleshooting method: Replace the rubber hose.

Answers to some questions about large bore cylinder:

How to repair the bent oil cylinder correctly?
If the bending oil cylinder leaks, the most direct way is to replace the seal ring. Most of the sealing rings used by domestic bending machines are made in Taiwan and Japan, so the service life of the sealing ring is still relatively long. If the bending oil cylinder used by the customer leaks oil, then when replacing the seal ring, be sure to choose a high-quality and durable seal ring. In this way, the replaced cylinder will not leak oil for a long time.

The diameter of the cylinder is 180mm and the pressure is 14mpa. How many tons can the cylinder hold?
Calculate the area of the cylinder, 3.14*9*9=254.34 square centimeters, take the approximate number of engineering, 1 mpa pressure is about 10 kg per square centimeter, 14 mpa pressure is 140 kg per square centimeter, that is 254.34*140=35607.6 kilograms, it can be known that the cylinder can be about 35 tons in theory.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女的bibi| 吃瓜AV直播免费在线观看| 国产肥熟一区二区精品视频| 鸡巴疯狂操B| 黄色录像aaaaa大片| 五月婷婷久久大香蕉视频综合网 | 五月婷婷成人AV网址| 男人的天堂乱辈通| 插女人小穴AV一区二区三区四区| 景德镇市| 亚洲av美女一区二区| 精品人妻少妇一二三区| 青青青青免费在线视频| 午夜操逼逼| 91婷婷激情| 人妻被操宓| 男女人操B视频| 国产精品对白真实在线观看| 色婷婷天天操| 日韩操逼大鸡巴| 中文字幕一曲二区三区四区| 操无码色| 92欧美在线| 精品传媒一区二区三区| 老司机福利免费三区| 亚洲AV色香蕉一区二区三区蜜桃| 免费公开视频不卡| 亚洲鸡吧| 大鸡巴操熟女黑毛大屄视频| 乳交日韩在线精品| 美女扒开尿口被人插久久| 成人大香蕉一区二区三区| 曰韩精品一区二区三区中文在钱 | 中文字幕一区无码| 偷拍区自拍| www.xx日本大香蕉| 麻豆果冻传媒在线观看视频免费入口 | 中文字慕一区二区不卡| 大鸡巴肏呦女视频| 红色五月综合网| 日韩美女骚穴|