亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

metallurgical cylinder Sold to El Salvador

Release time:2023-11-12 15:27:42 Hits: Current position: Home > News

This article mainly introduces:

El Salvador hydraulic cylinder,metallurgical cylinder manufacturer,metallurgical cylinder

El Salvador metallurgical cylinder

(El Salvador metallurgical cylinder,produced by Hebei Hengyu company)

metallurgical cylinder are widely used in El Salvador,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed metallurgical cylinder for customers from El Salvador.

Introduction to metallurgical cylinder:

metallurgical cylinder buffer valve inspection and maintenance: For the valve buffer metallurgical cylinder, the focus should be on checking the wear of the buffer valve spool and seat. Once it is found that the amount of wear increases and the seal fails, it should be replaced. It can also be repaired by using abrasive spool and seat matching grinding method.

The piston seal of the metallurgical cylinder is the main element to prevent leakage in the metallurgical cylinder. For the lip seal, it should focus on checking whether the lip edge is bruised and worn, and for the combination seal, it should focus on checking the wear of the sealing surface, and then determine whether the seal can be used. In addition, it is necessary to check whether the static seal between the piston and the piston rod is crushed. The piston rod seal should focus on checking the wear of the seals and supporting rings.

When the metallurgical cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

The material of the sliding part of the metallurgical cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

Answers to some questions about metallurgical cylinder:

How to control the speed of the cylinder?
High demand control, it is necessary to use servo closed-loop control, you can adjust the speed at will. Reference: Hydrodynamic Motion Control Practical Design Guide.

When the hydraulic cylinder changes from fast to slow, how can the slow speed become more even and the speed can be adjusted?
Reversing valve set 2 reversing valves. The back of one valve goes directly to the cylinder, running at full speed for fast action. Add a speed control valve behind the other valve, and then connect to the cylinder to achieve slow action, you can adjust the opening of the speed control valve, to achieve the speed of the cylinder can be adjusted. An import speed control valve to more than 1,000 yuan, if you think it is too expensive, you can also use the throttle valve instead. However, the throttle valve is greatly affected by the load change.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
av网站在线免费观看一区二区三区| 亚洲色婷婷久久久徖合日本| 美女大鸡巴操你| 色色av草草| 嘉善县| 妇女逼视频www| 黄色伊人一区二区三区| 日本一区二区尿尿在线| 国产日产欧美在线观看| 大香蕉曰裸模在线| 精产毛片免费看一二三| 嫩艹逼| 久久一区中文字幕不卡| 鸡巴插小穴操操操的免费网站| 嗯嗯啊在线的| 大肉棒一出一进的| 日本黄色1‘2‘3区’’| 性爱综合亚洲| 成人AV一级录像| 嗯嗯啊好大嗯嗯啊视频| 一卡二卡成人片| 嫩模深喉一区| 欧洲综合自拍亚洲综合图片区| 欧美草草视频| 欧美大鸡巴操逼逼谈话精选| 五月婷婷婷婷婷婷婷| 日韩欧美国产操逼| 毛片资源精品在线观看91av| 寡妇被猛烈进入30分钟| 亚洲爆乳人妻中文字幕第一页| 欧美 激情 另类 日韩在线观看 | 啊啊啊啊嗯嗯啊视频| 在线观看后入美女0| 主播被操视频| 日本韩国操穴| 熟女五十路一二三区| 用鸡巴肏死美女校花在线观看| 精品日韩熟女视频| 大几把久久久久久| 大香蕉亚洲视频在线观看| 一本色道久久亚洲AV蜜桃|