亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steering power cylinder Sold to Australia

Release time:2023-11-12 15:26:16 Hits: Current position: Home > News

This article mainly introduces:

Australia hydraulic cylinder,steering power cylinder manufacturer,steering power cylinder

Australia steering power cylinder

(Australia steering power cylinder,produced by Hebei Hengyu company)

steering power cylinder are widely used in Australia,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed steering power cylinder for customers from Australia.

Introduction to steering power cylinder:

When the steering power cylinder needs to be stored for a period of time, please follow the recommended methods: The steering power cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the steering power cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil steering power cylinder should not be in direct contact with water vapor for a long time. The steering power cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the steering power cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the steering power cylinder Before working, the steering power cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the steering power cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

steering power cylinder diameter, rod diameter, stroke determination: Choose national standards or other standards steering power cylinder, avoid the selection of non-standard size, otherwise the difficulty of processing and manufacturing costs will be increased. The length of the steering power cylinder guide is determined by the length of the stroke. Check the strength of steering power cylinder, piston rod, screw, etc. according to the working pressure or load. At the same time, working pressure, ambient temperature, working medium and running speed are also the key to selecting seals.

When the steering power cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the steering power cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

The steering power cylinder should not be mixed with foreign objects during assembly, which will cause scars. Before the total assembly of the steering power cylinder, all parts must be fully removed and cleaned. When the parts are installed with burrs or dirt, foreign objects are easily embedded into the surface of the steering power cylinder wall due to the stiffness and the weight of the parts, causing scars.

Answers to some questions about steering power cylinder:

By what means can the hydraulic system control the arbitrary stroke position of the rotary cylinder piston rod?
The following ways can be considered: 1, through the limit device, such as limit switch, position sensor, etc. 2, by feedback the pressure of the hydraulic oil in the cylinder. The load determines the pressure, the pressure in the cylinder is determined by the load, and the pressure is very small when the cylinder is unloaded. 2.1 When clamping the workpiece, the pressure of the cylinder increases, by calculating the relationship between the clamping force and the pressure of the cylinder, take a pressure value of the cylinder, set the pressure switch, and drive the valve to work when the pressure reaches the preset value, so that the oil circuit stops supplying oil. 2.2 or set the pressure value of the relief valve to overflow after a certain set pressure.

Is there a way to make the cylinder stop pushing when it hits something hard during the process of pushing?
The simplest solution is to press the stop switch, this switch has a mechanical type, touch the object on the action or send a stop signal, through the operation of the motor control cylinder; There is also an induction switch, that is, when the hydraulic cylinder expands to the range of the induction switch can sense the signal, it sends a signal to let the motor act, resulting in the corresponding action of the cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
狠狠色色综合| 女体化媚药在线观看| 免费日本熟妇视频| 国产高清国际精品福利色噜噜| 大鸡巴插光身大胸美女| 制服丝袜美女免费观看| 欧美综合婷婷综合五月精品| 亚洲男人的天堂A∨高清在线| 国产亚洲99久久精品熟女网站| 美女被射视频在线观看91| 一区二区三区在线观看...。。。| 大肉棒一进一出免费看视频| 丰满熟女视频一区二区| 一二三区免费在线| 成人午夜一区二区在线| 我想操逼操日本的逼| 啊啊啊男人使劲干视频一区二区| 国产偷拍日韩无码欧美视频| 亚洲成人熟女性爱视频| 男女人操B网站| 1有码视频在线精品| 日韩有码黄片子| 无码精品96| 老司机不卡视频一区二区| 香蕉九九| 波多野结衣 丝袜| 美女露出小穴视频| 精品蜜臀国产AV一区二区| 色五月亭综合| 啊快操我好爽啊啊啊视频| 黑人激情大吊| 操女人逼系列免費視頻| 美女操B网站www| 嗯啊嗯啊好舒服在线观看| 操逼啊啊嗯嗯视频| 欧美熟妇色二| 成人免费视频XNXX.COM| 大鸡吧操美女视频在线播放| 国内外免费成人小视频你懂的| 啊啊操我啊日韩| 少妇AV福利|