亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steering power cylinder Sold to Uzbekistan

Release time:2023-11-12 15:26:05 Hits: Current position: Home > News

This article mainly introduces:

Uzbekistan hydraulic cylinder,steering power cylinder manufacturer,steering power cylinder

Uzbekistan steering power cylinder

(Uzbekistan steering power cylinder,produced by Hengyu Group)

steering power cylinder are widely used in Uzbekistan,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed steering power cylinder for customers from Uzbekistan.

Introduction to steering power cylinder:

steering power cylinder spool stuck or valve hole blocked How to solve: When the flow valve or direction valve spool stuck or valve hole blocked, the steering power cylinder prone to misoperation or action failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium.

Because of the slightly complex structure of the buffer steering power cylinder, sometimes there will be problems, such as when the steering power cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

The pressure of the sliding surface of the steering power cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the steering power cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

When the steering power cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the steering power cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the steering power cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

Answers to some questions about steering power cylinder:

What is the meaning of cylinder ejection on the injection mold, and what is the difference between cylinder ejection and ordinary ejection?
Usually requires the front die ejection will use the cylinder to drive the thimble plate to achieve the ejection of the thimble. There is also a case that the mold is very large or long, and the balance of the ejector rod of the injection molding machine is not enough, and the cylinder ejector will also be used.

Why does excavator cylinder oil leak?
Under normal circumstances, the leakage of hydraulic cylinders is divided into internal leakage and external leakage. The external leakage is generally due to damage to the oil seal at the extended end of the piston rod and needs to be replaced. Internal leakage is generally because the oil seal on the piston is damaged, you can try to replace the oil seal here, if the replacement will also leak, then check whether there is damage to the inner wall of the cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
青娱乐波多野| 激情无码AV| 美国成年人噜噜噜| 国产人美﹣色哟哟91| AV在线一区二区的| 日韩 欧美 国产 亚洲| 中国操操逼| 久久丁香婷婷中文字幕| 超並区在线观看| www.日韩黄文| 大肉棒插小穴在线观看| 大吊操大黑逼| 伦理视频在线一区二区| 美女搞尿b| 插入大屁股骚妇| 呃呃啊啊免费性视频| 激情草草网| 看四川美女日逼视频| 日本 啊啊啊| 香蕉午夜视频| 黑人大吊亚洲娇小| 中文字幕二区视频在线观看| 国产在线五区| 色情大鸡巴插小穴视频| 天天干天天拍91| 天天橾夜夜夜| 一区二区福利在线| 亚洲AV中文| 看新加坡大鸡巴操小逼| 欧美精品逼逼逼逼逼逼逼| 人妻一区二区蜜桃| 国产精品丝袜一区二区三区四区| 国产日韩欧美一级操逼大片| 十八禁福利偷拍视频| 免费看美女的网站国产| 日韩成人图片视频小说| 中文字幕日本55| 狂插小美女视频| www.av男人的天堂| 我想看美女日逼视频| 大鸡巴插Bav|