亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hydraulic lifting cylinder Sold to Slovakia

Release time:2023-11-12 15:26:04 Hits: Current position: Home > News

This article mainly introduces:

Slovakia hydraulic cylinder,hydraulic lifting cylinder manufacturer,hydraulic lifting cylinder

Slovakia hydraulic lifting cylinder

(Slovakia hydraulic lifting cylinder,produced by Hebei Hengyu company)

hydraulic lifting cylinder are widely used in Slovakia,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed hydraulic lifting cylinder for customers from Slovakia.

Introduction to hydraulic lifting cylinder:

The assembly work of the hydraulic lifting cylinder has a great impact on the quality of the hydraulic lifting cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

When installing the hydraulic lifting cylinder, the axial ends of the hydraulic lifting cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the hydraulic lifting cylinder, there is axial expansion. If the two ends of the hydraulic lifting cylinder are fixed, all parts of the hydraulic lifting cylinder will be deformed. When disassembling the hydraulic lifting cylinder, it is strictly forbidden to hammer the hydraulic lifting cylinder and the piston surface, such as the hydraulic lifting cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

The method of sleeve hydraulic lifting cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the hydraulic lifting cylinder can be significantly improved by rolling in the finishing of the inner holes of the hydraulic lifting cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.

If the hydraulic lifting cylinder slips or crawls, please check whether there is astringency inside the hydraulic lifting cylinder, because the internal parts of the hydraulic lifting cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the hydraulic lifting cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the hydraulic lifting cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

Answers to some questions about hydraulic lifting cylinder:

How is the cylinder of hydraulic cylinder processed?
As the main parts of hydraulic cylinder, mining single pillar, hydraulic support, gun barrel and other products, its processing quality directly affects the life and reliability of the whole product. Cylinder processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of cylinder is deep hole processing, which has always troubled the processing personnel. Due to the residual compressive stress on the surface of the surface layer, the rolling machining is helpful to seal the small cracks on the surface and prevent the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the cylinder can be improved.

Can one hydraulic pump with two cylinders work?
A hydraulic pump with two cylinders will work. Commonly used hydraulic pump types: 1, according to whether the flow can be adjusted can be divided into: variable pump and quantitative pump. The output flow can be adjusted according to the needs of the variable pump, the flow can not be adjusted called quantitative pump. 2, according to the pump structure commonly used in the hydraulic system is divided into: gear pump, vane pump and plunger pump 3 kinds. Gear pump: small volume, simple structure, the cleanliness of the oil requirements are not strict, the price is cheaper; However, the pump shaft is subjected to unbalanced force, serious wear and leakage. Vane pump: divided into double acting vane pump and single acting vane pump. The pump has uniform flow, smooth operation, low noise, higher pressure and volumetric efficiency than gear pump, and more complex structure than gear pump.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
福利二区福利三区福利视频| 人妻斩4K岛国动作片| 亚洲一二三四AV| 五月婷婷一级免费电影| 亚洲精品口爆| 夜夜操夜夜夜| 鸡把擦小穴视频| ...中文天堂在线一区| 清远市| av一区二区在线观看完| 操美女小骚逼的视频| 加勒比无码果冻| 嗯啊 av| 午夜精品福利视频网| 韩国三级精品在线视频| 亚洲第一AV啊啊啊| 逼逼逼久久久| 欧洲久久久一区| 东京热论坛人妻| 91大神系列全集在线| 网站在线观看网站一二区| 骚鸡巴操逼| 夜夜操人人插| 深插91视频| 欧美一区二区性生活视频| 欧美侧少妇网站| 东京热AV无码| 五十路欧美女人的牲 | 欧美少妇性生活在线| 97超级香蕉在线视频免费| 用大鸡巴操死我喷水视频| 东乌珠穆沁旗| 抽插逼逼高潮啊啊啊| 亚洲专区在线播放韩国| 午夜人妻丰满少妇久久久| 污动漫免费视频欧洲| 国产1级Av片在线免费观看| 美女午夜写真福利视频| 视频一区二区蜜臀| chinese偷拍自| 欧美一区二区三区婷婷五月色婷 |