亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

extra high pressure cylinder Sold to Burma

Release time:2023-11-12 15:25:57 Hits: Current position: Home > News

This article mainly introduces:

Burma hydraulic cylinder,extra high pressure cylinder manufacturer,extra high pressure cylinder

Burma extra high pressure cylinder

(Burma extra high pressure cylinder,produced by Hebei Hengyu company)

extra high pressure cylinder are widely used in Burma,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed extra high pressure cylinder for customers from Burma.

Introduction to extra high pressure cylinder:

The extra high pressure cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the extra high pressure cylinder should pay attention to: the operation should be as far away from the extra high pressure cylinder as possible, to avoid falling objects, knocking, rubbing the extra high pressure cylinder coating. When cleaning the extra high pressure cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the extra high pressure cylinder when the oil temperature exceeds 70 ° C.

When the control pressure of the hydraulic system is too low, the extra high pressure cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

When the hydraulic oil is not pumped into the extra high pressure cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the extra high pressure cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

How the cavitation of the extra high pressure cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the extra high pressure cylinder, resulting in corrosive damage to the parts.

Answers to some questions about extra high pressure cylinder:

What welding rod is used for hydraulic cylinder welding?
There are several reasons for bad welding of hydraulic cylinder: 1. There is hydraulic oil on the welding surface, wipe it with a rag, there will be bubbles in the welding process, and it will not last for a few days. You have to remove it, drain it, wash it off with gasoline and try again. 2. Open the groove before welding, it is not deep enough to use the Angle grinding machine, and can not find the accurate crack position. 3. The material of the cylinder itself is not clear, the welding performance of more than 35 steel is not good, in the factory welding needs to preheat, the welding rod should also be dried and insulated, there is no such condition on the site.

Where's the hydraulic cylinder bleed valve?
There is a vent hole at the top of the cylinder next to the intake pipe. Generally, it can be used, and the air in the cylinder can be naturally drained after several moves.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女被操的视频网站在线观看视频| 艹死美女白虎| 蜜 臀A V北条麻妃在线播放| 鸡巴操穴流白浆视频| 在线0930无码| 中国精品女村女人操逼| 青青在线一区二区视频| 九九热三区| 美女流水的视频网站| 安庆市| 日韩和欧美成人在线视频| 美女操逼逼赖赖| 日本无码操穴视频| 女女同女女一区二区三区| 株洲市| ww.av.w| 逼亚洲欧美成人逼| 超超超超碰国产| 夜夜嗨五月| 岛国视频午夜福利三区| 日韩性爰视频网站| 后入猛操闺蜜小视频| 操美美女的鸡巴| 18 禁精品| 刘玥 一区二区三区视频| 西安精品一区到十一区在线| 日本18禁一区二区| 美女被曰视频| 美女被大鸡巴操软件| 国产一二三四五av在线| 中文字母三级片| 嗯啊后入嗯视频| search.打几把操逼| 日韩性生活网| 五月天伊人日本不卡一区| 91视频免费观看蜜臀| 爆操我的骚逼视频好爽不卡| 激情一区二区精品| 嗯嗯啊艹出 嗯啊嗯嗯啊艹视频| 操一操日一日| 少妇自慰99|