亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Jordan

Release time:2023-11-12 15:25:48 Hits: Current position: Home > News

This article mainly introduces:

Jordan hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Jordan swager cylinder

(Jordan swager cylinder,produced by Hengyu Hydraulic Co., Ltd)

swager cylinder are widely used in Jordan,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed swager cylinder for customers from Jordan.

Introduction to swager cylinder:

swager cylinder hydraulic oil selection: The recommended working oil viscosity of the swager cylinder is 10 ~ 110cSt (1.8 ~ 15E), ISO VG46 hydraulic oil. The normal working oil temperature is 10 ~ 70℃, and the ambient temperature is in the range of -20 ~ 80℃. When the ambient temperature and service temperature are low, the hydraulic oil with lower viscosity can be selected.

Classification of swager cylinder: according to the mode of movement it can be divided into linear reciprocating movement type and rotary swing type; According to the effect of liquid pressure, it can be divided into single acting type and double acting type. According to the structure, it can be divided into piston type, plunger type, multistage telescopic sleeve type, pinion and rack type, etc. According to the installation form can be divided into rod, earring, foot, hinge shaft and so on; According to the pressure grade can be divided into 16Mpa, 25Mpa, 31.5Mpa and so on.

When the swager cylinder is customized, if there are high requirements for the quality of the swager cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the swager cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the swager cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

When using the swager cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the swager cylinder block. If the swager cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the swager cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the swager cylinder, so that the working efficiency of the swager cylinder is reduced.

Answers to some questions about swager cylinder:

What is the problem that the cylinder stroke is not in place?
1. Mechanical cause: the piston rod bends; If there is a synchronous cylinder, the stroke of the two cylinders may be different. 2. Hydraulic reason: the system back pressure is too large; The actuator load increases while the system pressure decreases. The electric is not sent, the reversing valve is not reset or stuck, the oil is too dirty, there is gas in the system, the external inertia load is too large, and the cylinder stroke is not in place.

What is the difference between hydraulic piston cylinder and plunger cylinder?
The force surface of the piston cylinder is a rod cavity and a rodless cavity, and the force surface of the plunger cylinder is the plunger, the spring return single-acting piston cylinder can also rely on the external force of the spring to achieve return, the double-acting piston cylinder can produce tension, and the plunger cylinder only produces thrust without tension.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女摩擦大鸡吧在线免费观看| 蜜乳高清在线| 台湾佬22中文娱乐| av辣 久久 成人 动漫| 中文字幕区在线| 亚洲色欲色欲综合网站| 嗯嗯啊啊啊啊嗯在线播放| 国产福利尹人精品| 操爽你| 科技| 殴美黄片一区六区| 毛片一区二区三区四区五区六区| 大香蕉影音先锋色婷婷| 久久中文字幕国产| 国内少妇精品| 百度日韩大香蕉在线观看| 免费进入网站18 国产| 网站女生的大鸡巴| 国产又大又猛又粗又长| 夜夜操操天天干干| 中午福了美女大鸡巴| 日韩一级片黄| 国产AV探花系列| 女生的逼逼91| 操妻逼逼福利| 自拍大香蕉在线| 中文字幕三级片中出| 欧美成人精品一区二区三区视频| 人妻一区二区三区四区五区| www.草小逼| 轮台县| 男女抽插视频白浆| 午夜美女国产麻豆视频| 武隆县| 鸡巴嫰逼黄片| 欧美熟妇精品免费在线| 少妇爆乳自慰| 色五月综合综合| 性插少妇骚穴| 欧美.日韩精品·吻草| 人妻少妇久久在线观看|