亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

steering cylinder Sold to Bangladesh

Release time:2023-11-12 14:24:40 Hits:148 Current position: Home > News

This article mainly introduces:

Bangladesh hydraulic cylinder,steering cylinder manufacturer,steering cylinder

Bangladesh steering cylinder

(Bangladesh steering cylinder,produced by Hengyu Hydraulic Co., Ltd)

steering cylinder are widely used in Bangladesh,because of long service life,smooth movement,high work efficiency.So our company has designed steering cylinder for customers from Bangladesh.

Introduction to steering cylinder:

Because of the slightly complex structure of the buffer steering cylinder, sometimes there will be problems, such as when the steering cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the steering cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

How to determine the working pressure of the steering cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, steering cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

If the piston rod and steering cylinder are stuck or the steering cylinder is blocked, at this time, no matter how to operate, the steering cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the steering cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Answers to some questions about steering cylinder:

How does the hydraulic solenoid valve realize that the cylinder stops at any position?
Use an O-type medium function solenoid directional valve, or use a Y-type solenoid directional valve and a hydraulically controlled check valve.

Classification and application of cylinders.
Hydraulic cylinder is divided into single acting hydraulic cylinder, double acting cylinder, combined hydraulic cylinder, swing hydraulic cylinder. Single acting cylinder is divided into plunger type hydraulic cylinder, single piston rod hydraulic cylinder, double piston rod hydraulic cylinder, telescopic hydraulic cylinder. Plunger type hydraulic cylinder: the plunger moves only in one direction, and the return stroke is to push the plunger back using its own weight or load. Single piston rod hydraulic cylinder: The piston moves only in one direction, and the return stroke is to push the plunger back using dead weight or load. Double piston rod hydraulic cylinder: both sides of the piston are equipped with piston rods, and pressure oil can only be supplied to one side of the piston. The return stroke usually uses spring force, gravity or external force. Telescopic hydraulic cylinder: It obtains long stroke with short cylinder. The hydraulic oil is pushed out from large to small section by section, and the external force is reduced from small to large.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲日韩天天操| 外国夫妻精品视频| 晋宁县| 爽嫩 水 啊 视频 在线| 啊啊啊大鸡巴啊啊啊在线| 永久入口一区二区三区中文字幕| 日本一区二区视频91| 黄大仙区| 啊啊好爽嗯嗯啊在线观看| 嗯啊好痒啊好爽视频| 美女诱惑操B视频下载| 国产免费肛交| 超碰日本家庭抽播| 中文字幕乱码精品一区二区三区| 国产白浆aaacom| 南充市| 日本福利视频网站| 大香蕉视频青青| 美女张开鸡巴让男人捅| 男生爆操女生免费视频网站| 国产熟女一区二区三区黄| 台湾佬中文娱乐222.www| 熟女无码 北条| 色婷婷狠狠五月综合天色拍| 插播B视频| 大香蕉午夜福利局场| 亚洲熟妇av一区二区三区| 日逼无码视频免费看| 妓女avxxwww..com| 天天操小屄视频| 中文人妻丝袜后入| 北条麻妃一区二区系列| 怡红院最新| 亚洲免费乱码视频| 欧美高清网站| 女同一区二区九九| 一区怡红院综合| 大黑鸡巴插逼视频免费| 操老女人精品资源站| 大逼干大吊| 臀逼AV|