亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

yg series hydraulic cylinder Sold to Slovenia

Release time:2023-11-07 17:46:15 Hits: Current position: Home > News

This article mainly introduces:

Slovenia hydraulic cylinder,yg series hydraulic cylinder manufacturer,yg series hydraulic cylinder

Slovenia yg series hydraulic cylinder

(Slovenia yg series hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

yg series hydraulic cylinder are widely used in Slovenia,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed yg series hydraulic cylinder for customers from Slovenia.

Introduction to yg series hydraulic cylinder:

yg series hydraulic cylinder is the most important part of construction machinery, the traditional processing method is: broaching yg series hydraulic cylinder block - fine boring yg series hydraulic cylinder block - grinding yg series hydraulic cylinder block. The rolling method is: broaching yg series hydraulic cylinder block - fine boring yg series hydraulic cylinder block - rolling yg series hydraulic cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the yg series hydraulic cylinder block is about 1-2 days, rolling 1 meter of the yg series hydraulic cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the yg series hydraulic cylinder increases by 25%. If the yg series hydraulic cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality yg series hydraulic cylinders, you must take the rolling production process. After the yg series hydraulic cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

Disassembly yg series hydraulic cylinder: When disassembly yg series hydraulic cylinder, strictly prevent damage to the screw thread at the top of the piston rod, the screw thread of the yg series hydraulic cylinder head and the surface of the piston rod. It should also be noted that the piston cannot be played out from the yg series hydraulic cylinder.

yg series hydraulic cylinder buffer valve inspection and maintenance: For the valve buffer yg series hydraulic cylinder, the focus should be on checking the wear of the buffer valve spool and seat. Once it is found that the amount of wear increases and the seal fails, it should be replaced. It can also be repaired by using abrasive spool and seat matching grinding method.

If the piston rod and yg series hydraulic cylinder are stuck or the yg series hydraulic cylinder is blocked, at this time, no matter how to operate, the yg series hydraulic cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the yg series hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Answers to some questions about yg series hydraulic cylinder:

What is a mold core cylinder?
Simple plastic parts can be directly pushed out by the ejector rod after injection molding, complex plastic parts can not be directly pushed out by the ejector rod after injection molding, to make the interference part active, control its position through the cylinder (injection molding into the mold, so that the shape of the plastic parts meet the demand, exit after opening the mold, so that the plastic parts are smoothly pushed out), This kind of cylinder is the mold core cylinder.

How does the hydraulic solenoid valve realize that the cylinder stops at any position?
Use an O-type medium function solenoid directional valve, or use a Y-type solenoid directional valve and a hydraulically controlled check valve.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
操山东女人视频| AV在线1区2区3区| 美女草比逼逼| 大操B视频| 精品国产8000| 污视频在线观看免费国产| 中文无码一区二区不卡αv| 操欧美女人逼| 欧美美女野外操逼视频| 高清一区二区卡三区四区日本| 波少野结衣操大奶| 中文字幕欧美在线一区二区| 麻豆美女被操| 人人夹人人操| 欧美成人亚洲成人日本成人| 爆肏大嫩逼视频| 中文字幕一区无码| 四川操bb囗囗操| 大鸡巴狂插美女大屄视频| 一级片大鸡巴搞大骚逼| 操逼女人操逼| 被公侵犯一区二区| 国内在线观看免费一级av| 成人动漫av| 国产av一级二级三级| av狠狠插| 人妻出轨av中文字幕| 老妇一区二区三区▽| 男女操b视频和图片| 草莓成人性爱视频一区| 小鲜肉又爽又猛又深又粗网站| 日韩黄色网址丝袜人妻| 成人自拍一区| 99热久久久| 熟妇色小视频| 亚洲一区二区午夜福利中文字幕在线观看| www.91/东京热| 欧美日韩好色| 白虎逼插逼| 回产黄片网站| 大鸡巴操婊子逼视频|