亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

metallurgical cylinder Sold to Ireland

Release time:2023-11-12 14:24:35 Hits: Current position: Home > News

This article mainly introduces:

Ireland hydraulic cylinder,metallurgical cylinder manufacturer,metallurgical cylinder

Ireland metallurgical cylinder

(Ireland metallurgical cylinder,produced by Hengyu Hydraulic Co., Ltd)

metallurgical cylinder are widely used in Ireland,because of no transmission clearance,high work efficiency,long service life.So our company has designed metallurgical cylinder for customers from Ireland.

Introduction to metallurgical cylinder:

Factors that should be considered when selecting the oil seal in the metallurgical cylinder: some specific factors should be taken into account when selecting the oil seal in the metallurgical cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: metallurgical cylinder diameter, piston rod diameter, piston rod and piston groove size, metallurgical cylinder working pressure, metallurgical cylinder movement speed, hydraulic system oil temperature and metallurgical cylinder working environment.

After the metallurgical cylinder is installed, lubricating grease should be added to the relative moving parts such as earring and middle hinge shaft before trial operation.

The metallurgical cylinder is mainly composed of body, piston, piston rod, metallurgical cylinder head, metallurgical cylinder bottom, piston rod head and related auxiliary devices. The piston divides the metallurgical cylinder into two chambers, and moves reciprocally in the metallurgical cylinder with the help of pressure oil. In order to improve its working effect, there is no sealing ring on the piston to eliminate internal leakage, where the piston rod passes through the metallurgical cylinder head, due to the existence of the gap, it is easy to produce external leakage phenomenon, and the dust can enter the metallurgical cylinder through the gap, so the sealing device and dust prevention reason are set. At the same time, in order to eliminate the influence of eccentric load on the work of the piston, all the metallurgical cylinders must be provided with a considerable length of guide sleeve at the extended end of the piston rod. In addition, in the case of faster piston movement, the phenomenon of mechanical collision between the piston and the metallurgical cylinder bottom and the metallurgical cylinder head is serious, so the buffer deceleration should be set at both ends of the metallurgical cylinder The working medium of the metallurgical cylinder: because it works at room temperature, the ordinary oil-type hydraulic oil can be selected; metallurgical cylinder sealing device: The use of Yx sealing ring, polyurethane (PU) and polytetrafluoroethylene (PTFE) materials combined to achieve a good sealing effect; Buffer mechanism of the metallurgical cylinder: The buffer structure of the metallurgical cylinder is to prevent the piston from colliding with the metallurgical cylinder head at the end of the stroke.

We can not just consider the price and ignore the quality when we purchase the metallurgical cylinders. Now some manufacturers produce unqualified products in order to reduce costs, the piston rod is not adjusted, the rod coating is not enough, the metallurgical cylinder finish can not reach, the guide sleeve should use copper, but instead of ductile iron, although the cost is reduced, the quality of the metallurgical cylinder is not required.

Answers to some questions about metallurgical cylinder:

What is the pressure provided for a 63-bore cylinder with a pressure of 2 mpa?
2 mpa pressure is equivalent to 20 kg per square centimeter, 6.3 cm straight longitude, 3.15 cm radius, square, multiplied by, calculated an area of about 31.5 square centimeters, multiplied by 20 kg, the pressure is about 630 kg.

What are the reasons why the hydraulic cylinder action is slower than normal?
There are many factors that cause this problem. First, measure the pressure of the main system to see whether the pressure of the main system under the pressure state is consistent with the initial setting. Before measuring the pressure, it is best to check the hydraulic oil and suction oil filter and replace or clean it. Second, check the main relief valve of the reversing control multiway valve to see if there is damage or foreign matter blocking, and clean it. If your pump is a gear pump, the problem should generally be small. Second, look at traffic. There is no leakage in the cylinder, leakage in the reversing valve spool and so on.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
曰本电视居美男鸡巴和美女一级人| AV老司机午夜成人| www日本成人有码电影| 正在播放熟女五十路| 亚洲骚妇在线| 美腿丝袜亚洲区欧美日韩偷拍| 骚逼夜夜骚| 男女操b试看120秒| 欧美色白虎逼| 91n免费处女在线破视频免费观看视频 | 日本熟女中文字幕一区二区| 国产1990久久久久| 国产亂倫強姦高清晰片| 操美美女的鸡巴| 字幕av在线有码| 日韩欧尤物久久精品一区二区三区 | 国产熟女一区二区三区美国| 国产另类在线视频| 亚洲激情文学| 日韩欧美俄成人| 蜜桃AV极品蜜桃臀上位| 熟女丝袜人妻| 中文字幕蜜臀av| 操老太太逼视频网站| 连山| 人妻五十性大片| 成人主播一区二区| 大鸡巴操逼喷水爽| 欧美人,操日本女人| 亚洲av国产一区二区| 久久亚洲精工无码| 日本背德人妻| 欧美色图片一二三区| 久热久操一区| 欧美三区四区啊啊啊啊啊啊啊| 国产精品午夜婷婷| 国产精品探花视频在线| 大香蕉热女| 淫荡一区在线看网页| 亚洲熟女jjdhsjjndkkd| 女人的逼被我操视频|