亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

yg series hydraulic cylinder Sold to Belgium

Release time:2023-11-12 14:24:21 Hits: Current position: Home > News

This article mainly introduces:

Belgium hydraulic cylinder,yg series hydraulic cylinder manufacturer,yg series hydraulic cylinder

Belgium yg series hydraulic cylinder

(Belgium yg series hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

yg series hydraulic cylinder are widely used in Belgium,because of no need for deceleration device,long service life,smooth movement.So our company has designed yg series hydraulic cylinder for customers from Belgium.

Introduction to yg series hydraulic cylinder:

Analysis of commonly used seals: The wear ring and slip ring commonly used on the yg series hydraulic cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

The cavitation of the yg series hydraulic cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the yg series hydraulic cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

When installing the yg series hydraulic cylinder pipe, the pipe should be cleaned after installation, and should not pass through the yg series hydraulic cylinder block, and the by-pass pipe must be installed in front of the oil port of the yg series hydraulic cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the yg series hydraulic cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the yg series hydraulic cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Before purchasing the yg series hydraulic cylinder, it is necessary to master the original information and design basis, mainly including: the use and working conditions of the machine; The structural characteristics, load conditions, stroke size and operation requirements of the working mechanism; The selected working pressure and flow of the hydraulic system; The reality of materials, fittings and processes; Relevant national standards and technical specifications, etc.

Answers to some questions about yg series hydraulic cylinder:

Slide weight 35 kg exit stroke 55mm, is it suitable to use 40 cylinder diameter cylinder?
The maximum output force of the 40-bore hydraulic cylinder can reach 2 tons, and whether it can be used depends on the use scenario. In addition, the problem of mechanism stuck has nothing to do with the size of the power source, and reasonable structural design and good machining and assembly accuracy are the key.

PLC+ inverter + motor + pump + solenoid valve + cylinder combination, can control the accuracy of cylinder position?
In the case of extremely high accuracy requirements, you can not, please consider a few problems: 1, hydraulic oil can be compressed, it is elastic like a spring. Therefore, in the general hydraulic servo system, the valve control is far more accurate than the pump control. Because the valve can be installed very close to the hydraulic cylinder, or even installed on the hydraulic cylinder, but the pump must go through the tubing and then into the hydraulic cylinder, there is a long distance, which greatly reduces the rigidity of the system and increases the difficulty of control. 2, the quantitative pump is first of all leaking, and there is 10%-20% flow pulsation. Secondly, and more unfortunately, the leakage of the pump is related to the pressure and is non-linear.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲一区二区日韩精品AV| 日逼逼视频免费观看| 抽 插视频免费| 日本欧美国产91| 日本熟妇久日| 狠狠躁久久躁欧美黑人网站| 国产任你草精品视频免费| 欧姜福利视频| 国产级I成人院一区二区三区不卡| 在线天堂资源中文| 亚洲一区二区三区美女在线视频| 制服丝袜诱惑第一页| 在线免费AV导航| 大香蕉在线观看,国产| 国产传媒精品三区| 极品美女一区二区三区| 黑丝袜美女逼被操的视频软件| AV成人小骚| 日本不卡一区二区三区旧区五区区六| 啊啊…嗯嗯…嗯视频| 久久青青热| 人妻 有码 中文| 色综合15| 男人的天堂AV免费| 抽插到高潮的视频| 色老熟女欧美| 麻豆传媒在线一级二级| 襄垣县| 狠狠熟女亚洲| 国产成人午夜福| 欧美精品一区二区三区久久狼| 啊啊啊我要视频| 国产日韩欧美黄片在观看| K频道一区二区三区| 欧美在线免费视屏| 亚洲欧美另类激情综合区粉芽| 欧美激情午夜性生活| 日本日日夜夜夜夜夜| 大鸡巴操美女大屁股眼子视频| 日本成人福利片| 日本美女天堂|