亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

vehicle hydraulic cylinder Sold to Angola

Release time:2023-11-12 14:24:14 Hits: Current position: Home > News

This article mainly introduces:

Angola hydraulic cylinder,vehicle hydraulic cylinder manufacturer,vehicle hydraulic cylinder

Angola vehicle hydraulic cylinder

(Angola vehicle hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

vehicle hydraulic cylinder are widely used in Angola,because of long service life,smooth movement,high work efficiency.So our company has designed vehicle hydraulic cylinder for customers from Angola.

Introduction to vehicle hydraulic cylinder:

If the vehicle hydraulic cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

In the process of using the vehicle hydraulic cylinder, sometimes such a problem will occur, the vehicle hydraulic cylinder can not act immediately after the instruction of the vehicle hydraulic cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil vehicle hydraulic cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

The difference between the plunger vehicle hydraulic cylinder and the piston vehicle hydraulic cylinder is that the piston in the vehicle hydraulic cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type vehicle hydraulic cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

In order to ensure the service life of the vehicle hydraulic cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

Answers to some questions about vehicle hydraulic cylinder:

How to repair if hydraulic shears cylinder oil leakage?
The hydraulic cylinder is generally disassembled and the sealing ring is replaced. There are generally two ways to install the ends of the hydraulic cylinder. The larger hydraulic cylinder is mostly flanged disc type, which is screwed to the middle cylinder block by several bolts, the bolts are removed, and the cylinder head is slowly pulled out. The smaller hydraulic cylinder, the cylinder block and the head itself are threaded, and the rotating end cap can be removed from the cylinder block. If you do not understand the hydraulic cylinder, it is best to ask someone to deal with it. It is easy to damage the sealing ring and internal surface during disassembly.

There are four cylinders in the front top of the dump truck. When the second cylinder is lifted to half the height, it suddenly falls back more than 30 cm or so, and the cylinder continues to lift.
The problem is the cylinder, the second section of the different strength of the heart. When the oil supply resistance is small, the first out, when the power is not moving, the cylinder needs to be strong, because the second section needs to pop it out after a while when the pressure is large, the oil can not keep up, so it falls back, and the oil continues to keep up.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日本红怡院2020| 艳妇乳肉豪妇荡乳AV无码福利艳妇| 操插人妻av| 野外白虎少妇| 又深又粗 精一区二区| 日本一二区视频在线观看| 美女的鸡巴操| 日韩亚洲欧美国产成人五区| 熟女 人妻 人妻のAV| 一区二区91| 办公室丝袜爆乳国产一区| 97精品大香蕉在线| 操骚妇大屁股| 福利大香蕉短片视频在线观看| 欧美日韩美女屁股被操| 肥臀熟妇真爽一区二区| 大石桥市| 抽插视频白浆| 东京一区二区精品| 日韩操逼一级毛片| 国产激情传媒在线观看| 囤严精品一区| 大鸡巴干女| 综合十二月激情网| 舔骚bb视频插入大鸡巴视频| 污资源视频网站在线免费观看| 日本熟女丝袜综合网| 日本成人网一区二区| 日本人超碰免费观看| 超碰在线一区二区三区| 老司机精品视频伊人| 99视频久久五月婷婷| 日黑逼高清视频| 中文字幕人妻av蜜臀| 激情都市综合五月| 大香蕉在线欧美在线视频| 中文字幕乱码中出高清一区二区| 国产精品操逼大全| 男生桶爽女生视频在线观看| av(骚妇)在线| 白白色免费视频一区二区在线|