亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

track steering cylinder Sold to Colombia

Release time:2023-11-12 11:05:58 Hits: Current position: Home > News

This article mainly introduces:

Colombia hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

Colombia track steering cylinder

(Colombia track steering cylinder,produced by Hebei Hengyu company)

track steering cylinder are widely used in Colombia,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed track steering cylinder for customers from Colombia.

Introduction to track steering cylinder:

In the case of serious wear on the inner surface of the track steering cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the track steering cylinder manufacturing process for replacement. The track steering cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

The difference between the plunger track steering cylinder and the piston track steering cylinder is that the piston in the track steering cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type track steering cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

Most of the failure of the track steering cylinder is because there is a foreign body in the track steering cylinder into the failure of the track steering cylinder, the most problematic is that it is difficult to determine when the foreign body is into the track steering cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

When installing the track steering cylinder pipe, the pipe should be cleaned after installation, and should not pass through the track steering cylinder block, and the by-pass pipe must be installed in front of the oil port of the track steering cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the track steering cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the track steering cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Answers to some questions about track steering cylinder:

How to distinguish loader boom and forearm hydraulic cylinder? Is it the upper arm or the lower arm?
The one in the middle that can flip the bucket is the small arm cylinder you say, and the one that lifts the brackets (big arms) on both sides is the big arm cylinder.

Servo cylinder control principle
The electro-hydraulic pulse servo cylinder is composed of a stepper motor, a three-position four-way servo valve, a mechanical feedback device (a wire carrier) and an oil lever. When the stepper motor gets a pulse signal, its output shaft rotates 1.5 or 3 degrees, the servo valve spool drives the wire to rotate at the same time, the valve spool moves and opens the reversing cylinder to output pressure oil, the piston moves and drives the lead screw to reverse rotate the valve spool back to the original position, and the servo valve stops output pressure oil in the center. At this time, the cylinder moves 0.1 or 0.2mm stroke, and the displacement and speed of the cylinder travel are determined according to the given value of the electrical pulse.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女久久一二三| 欧美精品自拍无码视频在线| 污视频网址欧美| 欧美视频上下无遮挡| AV在线男人的天堂观看网站| 白天操夜晚上操白白操| 激情欧美日韩精品| 日本人人艹视频| 女生操BAV| 护士AV在线| 欧美日韩一区性爱麻豆国产视频 | 欧美插入操了| 一期二期日韩精品视频中国妓女| 男人把女人捅到暴爽免费| 遭B的免费视频| 亚洲人妻与欧美| 1区二二区三区无码| av情爱在线| 女主播被操在线播放| 在线观看日本艹b视频| 大鸡巴快用力操| 欧美一区二区大香蕉| 亚洲一二三区视频免费观看| 日韩美女性生活视频| 豪乳美女福利视频| 得得干在线成人观看| 欧美十二区| 男生操女生的逼视频网站| 日本一三不卡| 色五月婷婷中文字幕在线观看的网页| 黄色操逼欧美| 亚洲伍月婷婷| 红桃一区二区一区二区| 又大又长又爽又粗的黄片| 狠久久丝袜| 中文字幕之丝袜诱惑| 搞鸡操B在线看| 骚逼 骚逼 视频| 被操小视频| 大鸡巴疯狂抽插逼逼视频| 人人乐人人澡人人妻一二三区|