亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tilting furnace hydraulic cylinder Sold to Belgium

Release time:2023-11-12 11:05:56 Hits: Current position: Home > News

This article mainly introduces:

Belgium hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

Belgium tilting furnace hydraulic cylinder

(Belgium tilting furnace hydraulic cylinder,produced by Hengyu Group)

tilting furnace hydraulic cylinder are widely used in Belgium,because of no need for deceleration device,high work efficiency,excellent fatigue and impact resistance.So our company has designed tilting furnace hydraulic cylinder for customers from Belgium.

Introduction to tilting furnace hydraulic cylinder:

The tilting furnace hydraulic cylinder should be used as far as possible to avoid the transverse force, sometimes the piston rod to bear the transverse load is too large, especially do not force or pull the tilting furnace hydraulic cylinder, bite. Elimination method: When installing the tilting furnace hydraulic cylinder, ensure that the axis position of the tilting furnace hydraulic cylinder is consistent with the direction of movement; Make the load borne by the tilting furnace hydraulic cylinder as far as possible through the tilting furnace hydraulic cylinder axis, to avoid the phenomenon of eccentricity.

Under normal circumstances, the tilting furnace hydraulic cylinder is composed of the rear end cover, body, piston, piston rod and front end cover and other main parts. In order to prevent the working medium from leaking out of the tilting furnace hydraulic cylinder or from the high pressure chamber to the low pressure chamber, a sealing device (sealing ring) is arranged between the tilting furnace hydraulic cylinder and the end cover, the piston and the piston rod, the piston and the tilting furnace hydraulic cylinder, the piston rod and the front end cover. A dustproof device is also provided on the outside of the front end cover. In order to prevent the piston from impacting the end cap when it moves rapidly to the end of the stroke, the end of the tilting furnace hydraulic cylinder can also be provided with a buffer device. If necessary, the exhaust device should be set in order to exhaust.

If the tilting furnace hydraulic cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the tilting furnace hydraulic cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow tilting furnace hydraulic cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the tilting furnace hydraulic cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the tilting furnace hydraulic cylinder includes the leakage caused by excessive wear of the tilting furnace hydraulic cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and tilting furnace hydraulic cylinder, and the phenomenon of "pulling the tilting furnace hydraulic cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

When the tilting furnace hydraulic cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the tilting furnace hydraulic cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the tilting furnace hydraulic cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

Answers to some questions about tilting furnace hydraulic cylinder:

What valve is used to control the speed of the cylinder?
Hydraulic cylinder for lifting is generally the piston rod downward installation, to achieve the fast and slow speed of the cylinder, you can add a two-digit three-way electromagnetic reversing valve + a throttle valve on a branch at the bottom of the cylinder, you can achieve speed change, control mode can be controlled by time control can also be controlled by stroke switch. If you want to achieve more accurate control can use proportional valve control.

What is the valve on the hydraulic cylinder?
Oil valve, relief valve, overload valve, explosion-proof valve, etc., these are very convenient to insert! The oil valve, the overload valve and the blasting valve are very important for larger cylinders. Manufacturers will not offer you the selection. You need to choose the values by yourself according to your system, pump, cylinder, environment, working conditions and other comprehensive consideration!

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
快来插逼逼| 精品黑人巨吊| 美女少妇自慰 一区二区| 亚洲另类精品一二区| 人妻少妇美女| 性生活视频亚洲| 欧美色色欲| 国产老熟小视频| 91 碰 高清| 日韩吞精喝尿资源在线| 母与子的黄色性交片国产| 成人被操高潮网站| 欧美日韩在线观看草| 成人导航视频| 亚洲熟女人妻激情一区二区三区| 搞B的视频无码| 在线观看视频嗯啊嗯啊嗯啊| 久亚洲区二区| 女av一区| 熟女一区三区二区| 插骚穴视频在线观看| 日韩六十路人妻| 美女911区2区3区| 日韩躁小穴视频| 中文人妻第一页| 手机看片偷拍福利大屁股| 欧美久久福利久久大鸡巴| 青娱乐影视麻豆| 91无码在线视频一二三区| 苹果视频无码在线| AV网址大全一区二区三区| 麻豆激情网站| 嗯嗯啊啊啊啊啊视频免费观看| 日本女人操逼图片| 丰满黄色一级黄色片丰满大奶| 欧美高清小视频| 欧美粗大鸡巴操美女| 欧美日韩精品一级二级三级无码| 中文字墓在线一区不卡| 国产99久久绯色| 大香蕉123区在线看|