亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

vehicle hydraulic cylinder Sold to Japan

Release time:2023-11-12 11:05:34 Hits: Current position: Home > News

This article mainly introduces:

Japan hydraulic cylinder,vehicle hydraulic cylinder manufacturer,vehicle hydraulic cylinder

Japan vehicle hydraulic cylinder

(Japan vehicle hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

vehicle hydraulic cylinder are widely used in Japan,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed vehicle hydraulic cylinder for customers from Japan.

Introduction to vehicle hydraulic cylinder:

vehicle hydraulic cylinder spool stuck or valve hole blocked How to solve: When the flow valve or direction valve spool stuck or valve hole blocked, the vehicle hydraulic cylinder prone to misoperation or action failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the vehicle hydraulic cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

The quality of the vehicle hydraulic cylinder can not be ignored in the purchase of the vehicle hydraulic cylinder. The vehicle hydraulic cylinder is the main component of the vehicle hydraulic cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. vehicle hydraulic cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of vehicle hydraulic cylinder is deep hole processing, which has always troubled the processing personnel.

Under normal circumstances, the vehicle hydraulic cylinder is composed of the rear end cover, body, piston, piston rod and front end cover and other main parts. In order to prevent the working medium from leaking out of the vehicle hydraulic cylinder or from the high pressure chamber to the low pressure chamber, a sealing device (sealing ring) is arranged between the vehicle hydraulic cylinder and the end cover, the piston and the piston rod, the piston and the vehicle hydraulic cylinder, the piston rod and the front end cover. A dustproof device is also provided on the outside of the front end cover. In order to prevent the piston from impacting the end cap when it moves rapidly to the end of the stroke, the end of the vehicle hydraulic cylinder can also be provided with a buffer device. If necessary, the exhaust device should be set in order to exhaust.

Answers to some questions about vehicle hydraulic cylinder:

100 tons press, the cylinder diameter is 250, how much pressure?
100 tons hydraulic press, if it is a single acting hydraulic cylinder, the required oil pressure is the nominal force divided by the cross-sectional area of the cylinder piston. One hundred tons of its pressure is 1000 kN (1000000N), the diameter of the cylinder is 250 mm, its area is the circular rate multiplied by the square of the radius, is 49062.5 square mm, and then the pressure divided by the area of the oil pressure is 20.38MPa. Therefore, a hydraulic pressure of 20.38 mpa is required for a 250 diameter cylinder to obtain 100 tons of pressure.

Why does the tipping bucket cylinder have a cylinder withdrawal problem?
This problem may have a certain relationship with the operation of the driver, the main reasons are the following two situation analysis: 1, the current domestic loader working device is mostly a six-link mechanism, the six-link mechanism in the bucket to the limit position, lift the boom, the rotating bucket cylinder will appear "cylinder pulling" phenomenon, that is, the piston rod of the rotating bucket cylinder will be pulled out. In this case, in order to protect the cylinder, a pressure overload protection valve with large and small cavities is provided on the multi-way valve rotating bucket link (large chamber 18MPa, small chamber 12MPa). 2, before the cylinder is assembled to the whole machine, the cylinder is not limited, the piston rod of the cylinder can be pulled in place before and after, but when it is installed on the whole machine, in order to avoid the cylinder pulling out, the limit switch is installed according to the regulations.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
超碰咪咪爱av| 九九热未成年人精品蜜臀一区二区 | AV天堂牛牛牛| 一区二区啊啊a| 欧美日韩无删减| 操逼操逼操操逼逼| WWW666aV在线| 大香萑尹人| 日韩性爱xx在线观看免费视频| 亚洲一区三区三区导航| 无码人妻丰满熟妇精品区东京直播| 操大鸡吧电影| 亚洲一二在线观看4| 不遮不挡网站| 日韩欧美美女免费黄频| 啊好大好舒服视频| 人妻精品 每日| 嗯嗯嗯啊啊啊啊啊啊啊啊啊在线观看| 简单日逼精品视频A区大全部人| 操逼中国视频| 国产av街头| 天天干天天爱天天操| 成人天堂一区二区在线播放| 不卡1不卡2不卡3不卡4| 啊啊啊啊啊啊一区三区| 一二区AV在线| 国产粉嫩在线| 日韩AV一区二区三区 爱欲| 嗯嗯啊啊骚视频| 大鸡巴 暴操 美女| 人妻杂乱精品| 国产深夜操逼逼| 啊好大好爽好舒服操我视频| 镇远县| 亚洲有码 AV在线| 一区二区乱码中文字幕在线观看| 鸥美黄色一区二区| 中文字幕和亚洲有码视频| avtt无码一区中文一区| av激情网站| 爱在五月天激情网|