亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

yg series hydraulic cylinder Sold to Britain

Release time:2023-11-06 22:53:43 Hits:67 Current position: Home > News

This article mainly introduces:

Britain yg series hydraulic cylinder,yg series hydraulic cylinder manufacturer

Britain yg series hydraulic cylinder

(Britain yg series hydraulic cylinder,produced by Hengyu Group)

yg series hydraulic cylinder are widely used in Britain,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed yg series hydraulic cylinder for customers from Britain.

Introduction to yg series hydraulic cylinder:

Before the yg series hydraulic cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

The quality of the yg series hydraulic cylinder can not be ignored in the purchase of the yg series hydraulic cylinder. The yg series hydraulic cylinder is the main component of the yg series hydraulic cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. yg series hydraulic cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of yg series hydraulic cylinder is deep hole processing, which has always troubled the processing personnel.

yg series hydraulic cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the yg series hydraulic cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

When installing the yg series hydraulic cylinder, the axial ends of the yg series hydraulic cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the yg series hydraulic cylinder, there is axial expansion. If the two ends of the yg series hydraulic cylinder are fixed, all parts of the yg series hydraulic cylinder will be deformed. When disassembling the yg series hydraulic cylinder, it is strictly forbidden to hammer the yg series hydraulic cylinder and the piston surface, such as the yg series hydraulic cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

Answers to some questions about yg series hydraulic cylinder:

Is the hydraulic cylinder leaking because there is no pressure?
HC hydraulic cylinder common leakage reasons, first: most of the reasons are because the seal surface wear or aging leads to poor sealing, so there is no pressure to operate, as long as the piston seal can be replaced. Second: It may also be the piston rod strain, repair the piston rod is good. If it is because the piston strength is not enough and the playing time is long, it is necessary to replace the piston.

What is hydraulic cylinder guide?
The cylinder itself can not move, the piston moves, the guide should be used to guide the mechanism connected with the piston extension end. For example, in the commonly used hydraulic press, the guide column above is used to guide the pressure plate connected with the piston.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日美女毛B免费视频| 大香蕉net| 亚洲最大青涩网| 久久久久熟女一区二区三区| 欧美粗大免费在线| 韩国成人三级片在线看| 波多野结衣国产一区| 黑丝1区2区3区| 三级毛片网站青春草| 亚洲 日韩 欧美 中字 另类| 久欲热AV| 91看看视频小美女啪啪啪| 亚洲福利视频一区二区三区| 女同性精品 亚洲| 亚欧无码老太太视频| 男女后入试看120秒91| av婷婷五月天无码精品| 国产日韩欧美日日撸| 色欧美亚洲华人网| 日韩精品久久久久福利悠悠色| 美女干逼aV| 嗯啊嗯 啊插逼里视频播放| 想鸡巴操逼| 亚洲女性1区2区| 印度大鸡巴肏屄视频网站| AV东方国产在线一区| 精品熟女av色| 三上悠亚中文字幕一区二区三区| 操一艹日一日| 黑人与亚洲av| 不卡的日韩欧美| 日韩区二区三区中文字幕| 激情文学在线视频欧美| 嗯啊好痒啊好爽视频| 裸体人一区| 人妻中出一区| 国产三级内射| 色天堂污| 91大神高清在线观看| 日本美女极品中文字幕一区二区三区四区| 中文字幕一区二区三区在线观看每日更新 |