亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

electromagnetic induction cylinder Sold to New Zealand

Release time:2023-11-10 08:35:28 Hits: Current position: Home > News

This article mainly introduces:

New Zealand hydraulic cylinder,electromagnetic induction cylinder manufacturer,electromagnetic induction cylinder

New Zealand electromagnetic induction cylinder

(New Zealand electromagnetic induction cylinder,produced by Hengyu Hydraulic Co., Ltd)

electromagnetic induction cylinder are widely used in New Zealand,because of no need for deceleration device,long service life,smooth movement.So our company has designed electromagnetic induction cylinder for customers from New Zealand.

Introduction to electromagnetic induction cylinder:

The repair method of electromagnetic induction cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

electromagnetic induction cylinder piston rod material introduction: In general, we use 45 steel to produce electromagnetic induction cylinder piston rod. It has a large impact force when it is used, and some good performance steel are also used in the heavy load transmission. In order to have enough work intensity when using, and can ensure normal use, this is still more critical to have a detailed understanding of the material.

If the seal of the electromagnetic induction cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and electromagnetic induction cylinder, and the phenomenon of "pulling the electromagnetic induction cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

When the electromagnetic induction cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the electromagnetic induction cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the electromagnetic induction cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the electromagnetic induction cylinder can meet the requirements by grinding. However, the life and reliability of this repair electromagnetic induction cylinder are not high.

Answers to some questions about electromagnetic induction cylinder:

What is the reason for the hydraulic cylinder sticking out and not retracting?
There are two reasons: First, the problem with the seal, if there are two seals on the piston, the top seal is broken. Second, when the hydraulic pressure itself is designed, the rod cavity area is too small, so that the desired return force can not be achieved during the return trip. You can first check whether the coupling is damaged; Then see if the relief valve in the oil line block is blocked. If the use time is too long, it needs to be cleaned, the hydraulic oil is very dirty and can block oil block. Electromagnetic directional valves can also be checked, but the chance of problems is relatively small, unless there is a product problem.

What is the difference between hydraulic piston cylinder and plunger cylinder?
The force surface of the piston cylinder is a rod cavity and a rodless cavity, and the force surface of the plunger cylinder is the plunger, the spring return single-acting piston cylinder can also rely on the external force of the spring to achieve return, the double-acting piston cylinder can produce tension, and the plunger cylinder only produces thrust without tension.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
在线观看小视频| 欧美日韩成人Ⅴ| 亚洲日韩精品爆乳一区二区三区| 国产极品在线播放| 欧美一级性交黄片国产一级日韩一级| 激情成人日韩欧美| 一起草欧美国产日韩 | 免费黄片下载青青草视频| 亚洲日韩av一二三区精品| 美女女优一区二区| 大鸡巴狠狠操地铁上| 95AV麻豆蜜桃一区二区| 日韩大香蕉综合视频| 绝顶抽插av| 中字无码一区| 人人人人妻人人人人操区二区| 成人人妻文学视频| 美女被操后入| 日韩欧差在线综合网另类| 日韩美女主播三级| www日本成人有码电影| 日本一道一区二区三区视频| 涩五月网| 大香蕉日韩片| 嗯啊好大视频| 制服丝袜喷水| 蜜臀av少妇| 性色一区二区av| 精品深情五月视频12| 亚洲色图人妻偷拍| 欧美日本韩国午夜成人福利在线视频| 超碰婷婷| 亚洲丝袜美腿久久| 性感黑丝美女被男人操| 木下凛凛在线高清亚洲精品| 色涩涩综合| 蜜臀激情网| 大鸡吧艹骚逼| 日本爽视频二| 草逼内设| 殴美性爱一区二区三区不卡|