亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

unidirectional cylinder Sold to Romania

Release time:2023-11-06 22:53:37 Hits: Current position: Home > News

This article mainly introduces:

Romania unidirectional cylinder,unidirectional cylinder manufacturer

Romania unidirectional cylinder

(Romania unidirectional cylinder,produced by Hebei Hengyu company)

unidirectional cylinder are widely used in Romania,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed unidirectional cylinder for customers from Romania.

Introduction to unidirectional cylinder:

If the seal of the unidirectional cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

Protection of the unidirectional cylinder surface: During the dismantling process, safety protection should be carried out on the unidirectional cylinder to prevent objects from falling and welding slag from falling to the surface, causing damage to the unidirectional cylinder surface. In the process of propulsion, the damaged pipe segments should be prevented from falling and smashing, and the slurry remaining on the surface of the unidirectional cylinder should be cleaned up in time.

The repair method of the unidirectional cylinder: the repair of the unidirectional cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

Answers to some questions about unidirectional cylinder:

How to calculate the tonnage of the hydraulic press? Example: The input cylinder pressure is 5Mpa, the end area of the cylinder piston is 100mm, and how much is the thrust tonnage?
F=P*S=5*10^6*3.14*(1/20)^2=39250N.

What are the causes of hydraulic cylinder oil leakage?
First, between the piston rod and the guide sleeve: 1, the cylinder force is not good, there is a radial force between the piston rod and the guide sleeve there is a partial load, so that the oil seal is worn early, causing oil leakage. 2. The ambient temperature of the piston rod is high, especially radiant heat, and the oil seal aging is fast. 3. Whether the oil seal is selected correctly; Check whether the oil seal is damaged during installation. 4, guide sleeve and piston rod matching tolerance is correct. Second, between guide sleeve and cylinder: 1. Whether the O-ring on the guide sleeve is installed correctly, pay special attention to the O-ring can not "roll", especially some O-rings are die-pressed with a die-closing line. Third, common problems: 1, guide sleeve, cylinder, piston rod concentricity is poor. Fit tolerance is correct.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲国产精品午夜福利| 国产二级电影又粗又大| 国产亚洲欧美色片在线观看| 连续中出人妻| 亚洲aiai视频| 香蕉亚洲国产精品一区| 奇米| 又硬又粗又长一区二区三区视频| 婷亚洲中文| 国产日韩好欧美久久| 日美女B在线看视频| 男插女逼视频软件网站| 晋州市| 成人吸欧吸欧吸欧| 啊啊啊啊不要逼给你操烂视频| 色老头中文字幕| 国产激情专区| 尹人大香蕉操逼| 爱搞一区二区三区四区| 91激情视频在线| www.国产操逼| 一区二区三区五码久久| 大鸡吧综合色| 小骚逼破处视频| 欧美少妇流水视频| 国产精品夫妻内射| 美女操逼欧美| 玛纳斯县| 欧洲熟妇av天堂| 欧美日韩狂操| 亚州免費視頻一二三四五區| 一区二区久久综合插插| 91一区逼特逼在线| 蜜乳一区二区三区四区在线观看| 中文字幕在线观看一厂二厂三厂| 久久精品调教| 欧美日韩 成人| 鸡巴久久久久久久狂操| 中文无码字幕高清一区二区三区四区 | 尤物在线91| 91国产福利人妻精品|