亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tension cylinder Sold to Austria

Release time:2023-11-09 08:46:34 Hits: Current position: Home > News

This article mainly introduces:

Austria hydraulic cylinder,tension cylinder manufacturer,tension cylinder

Austria tension cylinder

(Austria tension cylinder,produced by Hengyu Hydraulic Cylinder Factory)

tension cylinder are widely used in Austria,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed tension cylinder for customers from Austria.

Introduction to tension cylinder:

tension cylinder can not drive the load troubleshooting: oil pressure is too low. tension cylinder selection specifications are too small. Leakage in tension cylinder or associated hydraulic system element.

The internal leakage of the tension cylinder should be prevented when the tension cylinder is used. The internal leakage of tension cylinder includes the leakage caused by excessive wear of tension cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

The oil tension cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

If the tension cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the tension cylinder. The internal parts of the tension cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the tension cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the tension cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the tension cylinder bore processing is out of whack. Because the piston and tension cylinder, guide rail and piston rod are relative If the tension cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling tension cylinder weight composition and calculation. The weight of the tension cylinder is composed of the tension cylinder diameter, the outer diameter and weight of the tension cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

Answers to some questions about tension cylinder:

How does the cylinder work?
Hydraulic transmission principle: oil as the working medium, through the change of the sealing volume to transfer movement, through the internal pressure of the oil to transfer power. 1. The power part - converts the mechanical energy of the prime mover into the pressure energy of the oil (hydraulic energy). For example: hydraulic pump. 2, the executive part - the hydraulic pump input oil pressure energy into the mechanical energy to drive the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3, the control part - used to control and adjust the oil pressure, flow and flow direction. For example: pressure control valve, flow control valve and direction control valve. 4, the auxiliary part - the first three parts are connected together to form a system, which plays the role of oil storage, filtration, measurement and sealing.

The two cylinders of the bending machine are out of sync?
Check whether the sliding slide is worn, adjust its tightness, so that both sides are consistent, check whether the two cylinder tubing is connected, tighten the flow valve, pressure, let the cylinder air discharge.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产极品粉嫩呻吟对白| 92国产精品午夜福利免费| 黄色极品视频在线| 日韩大香蕉导航| 中谷有希一区二区在线观看| 国产精品v日韩精品之超碰| 黄片| 在线播放爆插白虎| 亚洲清热久久一区丝袜| 青青草三级在线| 久久久久久亭亭| 操女人的骚逼视频/区| 欧美黑人大屌操逼| pacopacomama熟女人妻| 国产美女的鸡巴| 中日韩免费爱爱小视频 | 91N大鸡巴,好爽,用力| 国产裸模精品一区二区三粉嫩| 亚洲无限观看一区二区| 后入美女视频在线| 亚洲日韩高清性交| 日韩老少妇| 操B明星美女| 一本道中文AV| 欧美 日韩 国产 偷拍| 男人天堂av在线新地址| 人妻 日韩 欧美 综合 晨跑| 闫妮丰满熟女精品一区二区| 91腿模后入在线| 亚洲级女 片www91| 欧美爱爱2017久久| 操逼免费看啊啊啊啊再快点 | 超碰av一区二区在线播放| 国产成人午夜福| 大香蕉97视频在线观看公开| 日本女人体艺术麻豆视频女人体二区 | 偷拍自拍AV资源| 超碰国产在线直播| 欧美有码图片| 久久诱惑视频| 精品熟女肥臀一区二区三区三区 |