亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

spring return cylinder Sold to Azerbaijan

Release time:2023-11-09 08:46:26 Hits: Current position: Home > News

This article mainly introduces:

Azerbaijan hydraulic cylinder,spring return cylinder manufacturer,spring return cylinder

Azerbaijan spring return cylinder

(Azerbaijan spring return cylinder,produced by Hengyu Hydraulic Cylinder Factory)

spring return cylinder are widely used in Azerbaijan,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed spring return cylinder for customers from Azerbaijan.

Introduction to spring return cylinder:

In order to ensure the service life of the spring return cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

In the process of using the spring return cylinder, sometimes such a problem will occur, the spring return cylinder can not act immediately after the instruction of the spring return cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil spring return cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

When the control pressure of the hydraulic system is too low, the spring return cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

The spring return cylinder should be vented: when the spring return cylinder is installed or parked for a long time to work again, the air will penetrate into the spring return cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the spring return cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the spring return cylinder, the oil is best entered and discharged from the highest point of the spring return cylinder. spring return cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

Answers to some questions about spring return cylinder:

What's a minus 40 cylinder made of?
Construction with 1Cr18Ni9Ti, in low temperature conditions impact and tensile strength are very good, can withstand -100 degrees of low temperature, corrosion resistance, material price is not very high, more economic.

How is the hydraulic cylinder tempered?
The purpose of the tempering treatment is to make the piston rod have comprehensive mechanical properties of strength, hardness, plasticity and toughness, and the internal structure is uniform and fine tempered sorbite, so as to prepare the organization for subsequent surface quenching. The length of the long cylinder piston rod is 3800-4200, and the diameter is Φ90-Φ110mm, so its heating equipment uses a 150KW well resistance furnace or 600KW suspension continuous resistance heating furnace, and the temperature is controlled by two areas. Heat treatment process parameters: in the shaft furnace, a furnace is suspended with 4 pieces, the quenching heating temperature is 830±10℃, and after holding heat for 160min, it is divided into two times for quenching, and two pieces are quenched each time, and the circulating cooling water is used for cooling.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
婷婷五月男人| 亚州αv高清| 欧美黑人大吊操| 激情在线综合| 美女主播操逼网站| 法国丝袜熟女AV| 女人一区二区三区图| 亚洲熟女一区二区二区| 日韩AV中字有码| 大黑黑鸡巴操女女网| 肉感压迫丰满一区二区| 女人正宗日逼视频在插放| 美女抽插流白浆视频| 人人妻人人澡人人爽人人做爰| 欧美操逼。| 日本韩国激情网| 又黄又硬激情视频| 日韩丝袜美腿一区二区三区| 岛国日本午夜福利| 在线字幕高清二区三区| 欧美是韩国产在线观看| 男女啪啪猛烈无遮挡毛片| 啊插进去了视频| 操波多野结衣的逼| 欧美一区二区三区老太婆性生活| 色老女人欧美| 肥熟女精品视频| 一级在线录像| 红桃AV在线一区二区| 超碰在线无码AV| 亚洲有码视频观看在线| 草我嗯啊| 午夜不卡福利视频| 欧美日韩精品一级二级三级无码| 国产免费嘿咻视频在线观看| 欧美操逼。| 日韩av中文字幕三上悠亚| 美女磨擦视频网站| 欧美大鸡巴大屁股| 成人av六区| 啊啊啊嗯嗯,|