亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

track steering cylinder Sold to Burma

Release time:2023-11-09 08:46:19 Hits: Current position: Home > News

This article mainly introduces:

Burma hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

Burma track steering cylinder

(Burma track steering cylinder,produced by Hebei Hengyu company)

track steering cylinder are widely used in Burma,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed track steering cylinder for customers from Burma.

Introduction to track steering cylinder:

track steering cylinder spool stuck or valve hole blocked How to solve: When the flow valve or direction valve spool stuck or valve hole blocked, the track steering cylinder prone to misoperation or action failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium.

When installing the track steering cylinder, the axial ends of the track steering cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the track steering cylinder, there is axial expansion. If the two ends of the track steering cylinder are fixed, all parts of the track steering cylinder will be deformed. When disassembling the track steering cylinder, it is strictly forbidden to hammer the track steering cylinder and the piston surface, such as the track steering cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

When the track steering cylinder is repaired, its inner and outer diameter and roundness should be accurately measured. If the inner hole of the track steering cylinder is badly worn, it can be repaired by grinding the mandrel or honing on the boring machine. If the piston is worn, it can be repaired by electroplating, and serious wear should be replaced.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the track steering cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

Answers to some questions about track steering cylinder:

Cylinder pressure calculation formula
The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate it according to the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the working pressure P (unit MPa) the thrust of the cylinder F push =3.14*R*R*P (unit N) The pulling force of the cylinder F pull =3.14* (R*R-r* R) *P (unit N).

How do hydraulic equipment and hydraulic cylinders maintain a certain pressure after pressing to a certain position?
There are several methods. 1. You can use a constant pressure variable pump to adjust the control pressure of the pump to the pressure required by the cylinder, so that when the cylinder is in place, the pump uses the minimum flow rate to maintain the pressure, and the system is more energy saving. 2. If the pressure is maintained for a short time, a hydraulic control check valve can be added to the oil inlet end of the cylinder to close the cylinder and maintain the pressure. If the volume of the cylinder is large, an accumulator can be added between the valve and the cylinder to maintain pressure for 10-30 minutes. 3. You can add a small flow pump, the large pump after unloading, the small pump has been running, specifically for maintaining pressure.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日本传媒一二区| 五月天中文成人| 中文字幕 一区二区三区在线视频 日韩欧美中文字幕在线视频三区 欧美男女高潮操b | av天堂美女大鸡巴| 久久久日韩在线| 中文字幕成人在线精品观看| 免费超碰在线观看| 国产一区二区毛片A片婬片| 婷婷五月视频网站| 亚洲成人精品av| 男女操B绿冒| 加勒比 中文字幕 日韩 一区| 在线a一片| 外国美女被操网站| 白虎粉嫩的美女淫乱视频久久久| 去干网欧美最新版本| 五月婷婷涩涩激情在线| 波多野结衣一区二区三区小说| 91丨九色丨农村老熟女按摩| 性爱激情网| 中国年轻漂亮美女操逼动态图| 国精品无码一区二区三区在线| 久久肥女精品吃鸡巴| 久久九九性生活视频| 欧美日韩视频国产高清| 亚洲女人操比人人操| 国产女同调教资源| 一区二区日本免费中文字幕| 鸡巴艹逼逼逼穴| 大鸡吧肏黑屄视频| 97大香蕉在线 国产| 国产又大又粗的视频| 1久久人妻一区精品| 麻豆╳视频| 毛茸茸的大骚逼| 操鸡在线| 福利二区福利三区福利视频| 色婷婷五色综合小说| 视频一区少妇熟女人妻| 三上悠亚亚洲二区| 欧美大香蕉手机在线视频|