亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

self-locking hydraulic cylinder Sold to Malaysia

Release time:2023-11-09 08:46:11 Hits: Current position: Home > News

This article mainly introduces:

Malaysia hydraulic cylinder,self-locking hydraulic cylinder manufacturer,self-locking hydraulic cylinder

Malaysia self-locking hydraulic cylinder

(Malaysia self-locking hydraulic cylinder,produced by Hengyu Group)

self-locking hydraulic cylinder are widely used in Malaysia,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed self-locking hydraulic cylinder for customers from Malaysia.

Introduction to self-locking hydraulic cylinder:

How to determine the working pressure of the self-locking hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, self-locking hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

self-locking hydraulic cylinder hydraulic oil selection: The recommended working oil viscosity of the self-locking hydraulic cylinder is 10 ~ 110cSt (1.8 ~ 15E), ISO VG46 hydraulic oil. The normal working oil temperature is 10 ~ 70℃, and the ambient temperature is in the range of -20 ~ 80℃. When the ambient temperature and service temperature are low, the hydraulic oil with lower viscosity can be selected.

The commonly used buffer structure of the self-locking hydraulic cylinder is composed of a piston boss and a self-locking hydraulic cylinder head groove. When the piston moves close to the self-locking hydraulic cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

When the self-locking hydraulic cylinder needs to be stored for a period of time, please follow the recommended methods: The self-locking hydraulic cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the self-locking hydraulic cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil self-locking hydraulic cylinder should not be in direct contact with water vapor for a long time. The self-locking hydraulic cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the self-locking hydraulic cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the self-locking hydraulic cylinder Before working, the self-locking hydraulic cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the self-locking hydraulic cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

Answers to some questions about self-locking hydraulic cylinder:

Injection molding machine die thimble on the side of the feed nozzle, the oil cylinder pull the thimble shift, how to debug the oil cylinder?
The cylinder is connected with the neutron of the injection molding machine, the neutron is retreated after the opening mold is in place, the cylinder taps the thimble plate to the top, and then takes, and the neutron is reset.

What causes hydraulic cylinder oil leakage?
1. Internal leakage (1) The wear ring on the piston is seriously worn, leading to friction between the piston and the cylinder liner, and finally strain the cylinder liner, piston and seal; 2) Seal long-term use failure, piston seal (mostly U, V, Y ring, etc.) aging; 3) The hydraulic oil is dirty, and a large number of impurities enter the cylinder and wear the piston seal to bad; 2. External leakage 1) cylinder inlet and outlet tubing joint cracking; (This I see in the actual work is still more) 2) The piston rod extension end with the piston rod seal damage, mostly due to the piston cylinder is caused by hair, but also caused by aging; 3) The seal between the extended end of the piston rod and the liner is damaged.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩男人女人色情视频网站| 亚洲日韩一区二区三区四区高清在线观看| 被黑人鸡巴挤入视屏| 久久人体一区二区三区| 啊啊嗯嗯唔在线观看| 双男奶头免费视频下载| 美女丝袜勾引久久久一区| 美女扒开尿道让男人捅| 亚洲日韩欧美五月| 一区二区三区婷婷| 熟女精品一区二区视频| 深爱激情网第五页| 大鸡巴插欧美美女屁眼| 先锋影音 自拍偷拍| 桃花洞洞逼| 福利视频偷拍| 无码性交9区| 香港| 台湾佬中文娱乐圈222| 久久熟女精品| 日韩无码Ab| 日韩无码人体艺术1区2区3区| 97人妻大香蕉在线网站| 欧美伦理大香蕉视频在线观看| 操麻豆美女| 大鸡巴 操逼| 大基吧操骚逼| 红桃视频综合啪啪啪一区二区| 鲍鱼白虎美女视频在线直播免费观看| 非州精品一区二区三区| 亚洲一二区电影在线观看免费观看| 操的好舒服欧美| 成人在线视频人妻3P| 日韩美女白虎图片网址| 超碰在线下载页面| 韩国强奸变态少妇三级片X| 骚逼国产女| 天天爽天天干天天做夜夜操| 国产精品性色在线播放| 亚洲啪啪天堂| 欧美 网站 免费|