亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

single rack cylinder Sold to UAE

Release time:2023-11-09 08:46:10 Hits: Current position: Home > News

This article mainly introduces:

UAE hydraulic cylinder,single rack cylinder manufacturer,single rack cylinder

UAE single rack cylinder

(UAE single rack cylinder,produced by Hengyu Hydraulic Co., Ltd)

single rack cylinder are widely used in UAE,because of no need for deceleration device,long service life,smooth movement.So our company has designed single rack cylinder for customers from UAE.

Introduction to single rack cylinder:

single rack cylinder is the most important part of construction machinery, the traditional processing method is: broaching single rack cylinder block - fine boring single rack cylinder block - grinding single rack cylinder block. The rolling method is: broaching single rack cylinder block - fine boring single rack cylinder block - rolling single rack cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the single rack cylinder block is about 1-2 days, rolling 1 meter of the single rack cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the single rack cylinder increases by 25%. If the single rack cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality single rack cylinders, you must take the rolling production process. After the single rack cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

single rack cylinder buffer valve inspection and maintenance: For the valve buffer single rack cylinder, the focus should be on checking the wear of the buffer valve spool and seat. Once it is found that the amount of wear increases and the seal fails, it should be replaced. It can also be repaired by using abrasive spool and seat matching grinding method.

When the control pressure of the hydraulic system is too low, the single rack cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

single rack cylinder body inspection: The inner surface of the single rack cylinder and the piston seal are the main factors causing the leakage in the single rack cylinder, if the single rack cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the single rack cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

Answers to some questions about single rack cylinder:

How to disassemble the big nut that excavate the oil cylinder piston of the excavator?
If you want to be safe, look for a special unloading place for this thing, which is an oil cylinder on top of a turntable with a large nut attached to the center of the turntable. If you're in the field just pin the head of the cylinder to one end, use a big homemade wrench to hold the nut in place, and then get a digging machine and push it down, and it opens.

How to calculate the cross-sectional area of hydraulic cylinder?
Hydraulic cylinder cross section integral rod cavity and rodless cavity: rod cavity is cylinder inner wall cross-sectional area - piston rod cross-sectional area; The rodless cavity is the cross-sectional area of the inner wall of the cylinder. If the working pressure p and the output force F are known, the effective cross-sectional area A=F/p can be calculated.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
超碰一福利电影| 啪啪试看福利| 两个大鸡巴操逼| 操小美女的小逼视频| 久久色五| 日韩嗯嗯啊啊啊啊啊视频免费在线观看了 | 啊啊啊~嗯嗯~在线观看| 人妻上班偷人在线| 国产精品wwww美女视频| 啊啊啊好爽好痛视频| 日本视频三区| 国产精品夫妻互换x88a| 操古代美女小逼视频| 日韩熟女中文视频| 丝袜aV性爱| 草大鸡巴一区| 用力操我逼好爽好舒服免费观看| 国产精品尤物一区二区三区| 中文字幕诱惑勾引一区| 色哟哟哟www精品视频观看软件| 亚洲熟女AV和综合熟女AV| 欧美国产地址| 手机在线观看日韩AV| 嗯嗯啊啊嗯嗯嗯嗯嗯嗯在线| 欧美爱爱视频二区| 久久十热热| 大粗鸡巴操亚洲夫妻视频| 嗯啊什么嗯嗯视频| 色诱呦一区二区| 亚洲AV无码一区二区三区A日韩| 激情五月四播房| 金昌市| 国产又爽又粗又硬的视频| 丝袜黄片国产金牛| 二区三区四区视频不卡在线观看| 啊啊啊一区二区精品| 欧美少妇在线| 激情五月播播91深爱 | 国产导航精品视频一区二区 | 日韩在线啪| 水蜜桃一区二区三区|