亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to Costa Rica

Release time:2023-11-08 15:23:54 Hits: Current position: Home > News

This article mainly introduces:

Costa Rica hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

Costa Rica trunnion cylinder

(Costa Rica trunnion cylinder,produced by Hebei Hengyu company)

trunnion cylinder are widely used in Costa Rica,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed trunnion cylinder for customers from Costa Rica.

Introduction to trunnion cylinder:

trunnion cylinder buffer valve inspection and maintenance: For the valve buffer trunnion cylinder, the focus should be on checking the wear of the buffer valve spool and seat. Once it is found that the amount of wear increases and the seal fails, it should be replaced. It can also be repaired by using abrasive spool and seat matching grinding method.

The trunnion cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.

If the trunnion cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the trunnion cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow trunnion cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the trunnion cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the trunnion cylinder includes the leakage caused by excessive wear of the trunnion cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and trunnion cylinder, and the phenomenon of "pulling the trunnion cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

In use, the trunnion cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the trunnion cylinder.

Answers to some questions about trunnion cylinder:

What is the thin cylinder used for?
The principle is no different from ordinary cylinders, that is, the installation space is small, the formation is small, and it is suitable for some special occasions. For example, the space is compact and the place of small travel is used.

How does the cylinder of the shearing machine work?
Plate shear is a machine that cuts a sheet with a reciprocating straight motion from one blade to another. Through the moving upper blade and the fixed lower blade, the shear force is applied to the metal sheet of various thicknesses with a reasonable blade gap, so that the sheet is broken and separated according to the required size. Shearing machine belongs to one of the forging machinery, the main role is the metal processing industry. Products are widely used in aviation, light industry, metallurgy, chemical industry, construction, shipbuilding, automobile, electric power, electrical appliances, decoration and other industries to provide the required special machinery and complete sets of equipment. Working principle: The hydraulic system is used to drive the hydraulic cylinder to output a strong shear force to complete the shearing work.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日本女人天天干B| 精品国产8000| 美女骚穴舒服视频| 老司机开车AV| 熟妇的疯狂呻吟声| 福利www在线观看中文字幕不卡| 裕民县| 大香蕉日啪| 熟妇与大鸡巴| 亚洲美女观看| 美女操逼网站白虎骚逼蜜臀| 欧美激情一区二区在线视频| 欧美亚洲一区老妇| 日韩精品香蕉视频网| 高清丰满抽插白浆| 高清一级午夜福利67194| 中国妓女卖逼免费视频| 国产91熟女视频在线| 午夜日韩美女| 日韩欧美性爱成人片免费在线观看| 嗯啊操干视| 日韩人妻系列毛片| 日本伊人久久不卡| 国产一区二区污污污| 欧美美女淫乱视频一区二区三区| 欧美美女内射| 激情五月综合性W| 熟妇说小伙鸡巴好长能操到底了| 美女裸体无遮挡永久视频在线观看| 温宿县| 操老黑骚逼精品| 国产一区美女裸体操逼视频| 一本久久88中| 日美女日BB| 日产亚洲一区| 国产一区二区视频久久午夜| 自拍18页| 欧洲久久久毛片丶| 内射内射啪啪啪黑丝美女| 白逼免费视频观看| 兴城市|