亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stainless steel cylinder Sold to Sri Lanka

Release time:2023-11-08 10:37:13 Hits: Current position: Home > News

This article mainly introduces:

Sri Lanka hydraulic cylinder,stainless steel cylinder manufacturer,stainless steel cylinder

Sri Lanka stainless steel cylinder

(Sri Lanka stainless steel cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stainless steel cylinder are widely used in Sri Lanka,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed stainless steel cylinder for customers from Sri Lanka.

Introduction to stainless steel cylinder:

The stainless steel cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and does linear reciprocating motion (or swinging motion). It is simple in structure and reliable in operation. When it is used to achieve reciprocating movement, the deceleration device can be eliminated, and there is no transmission gap, and the movement is smooth, so it is widely used in various mechanical hydraulic systems. The output force of the stainless steel cylinder is proportional to the effective area of the piston and the pressure difference between the two sides; The stainless steel cylinder is basically composed of stainless steel cylinder and stainless steel cylinder head, piston and piston rod, sealing device, buffer device and exhaust device. Buffer device and exhaust device depending on the specific application, other devices are essential.

stainless steel cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the stainless steel cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

The stainless steel cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure stainless steel cylinder can use 20 steel pipe, and the high pressure stainless steel cylinder can use 45 steel pipe.

When the oil pressure of the stainless steel cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

Answers to some questions about stainless steel cylinder:

What is the material of the lift cylinder?
The cylinder is composed of many parts. The cylinder also contains the seal and the installation port at both ends, the material of these two parts is not easy to determine if there is no physical object. The cylinder body is generally 20 steel, 45 steel, 27SiMn and other materials, and the piston rod is generally 40Cr, 45 steel and other materials.

How to calculate cylinder speed?
If there is a throttle valve, the cylinder speed will be adjustable. When the throttle is fully opened, the speed of the cylinder reaches the maximum: maximum speed = oil pump displacement ÷ cylinder cavity cross-sectional area The displacement of the oil pump is a main indicator, which can be found on the nameplate, and some can also be known by the oil pump model; The cross-sectional area of the cylinder cavity can be easily calculated. Just make sure the units are the same. And because the cross-sectional area of the rod cavity and the rodless cavity of the cylinder is different, the speed of advance and retreat may also be different.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美中文字幕超碰| 一级黄片50岁在线| 插逼视频高清无码| 操射的美女| 激情五月综合第一页| 亚洲性爱无码| 天天操夜夜2026| 啪啪亚洲中文字幕| 骚逼骚奶头| 国产人妻精品一区二区三水牛影视| 天天操夜夜干多人操| 亚洲一二三区无码视频| 高清视频黄色仓库免费| 大香蕉海外视频在线播放| 欧美日韩一级成人| 超碰日本电影| 欧美一级黄色片打炮| 久久久人妻黑丝| 色悠悠视频| 美女曰B视频看看| 亚洲国产一区二区三区不卡电影1 蜜臀av北条麻妃中文人妻 | 丛av二十区| 色呦呦一区二区三区在线观看 | 哪里可以看国产小夫妻自拍三级片| 鸡吧怼逼| 中文字幕导航一区二区三区导航| 欧美亚洲日韩理论片在线| 欧美熟女激情五月天四房播播| 美女全裸被操免费看| 高阳县| 亚洲操骚逼逼| 天天肏美女夜夜肏| 大鸡巴艹逼少妇高潮视频| 黑料在线视频一区二区| 制服诱惑丝袜中文字幕| 久久之夜黑| 操逼一区二区视频免费观看| 内射粉嫩人妻| 色婷婷在线观看视频免费观看视频| 日韩女优电影在线观看一区二区| 成人一区二区三区黄|