亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

large cylinder Sold to Colombia

Release time:2023-12-18 10:57:22 Hits: Current position: Home > News

This article mainly introduces:

Colombia hydraulic cylinder,large cylinder manufacturer,large cylinder

Colombia large cylinder

(Colombia large cylinder,produced by Hengyu Hydraulic Cylinder Factory)

large cylinder are widely used in Colombia,because of long service life,smooth movement,high work efficiency.So our company has designed large cylinder for customers from Colombia.

Introduction to large cylinder:

If it is found that the large cylinder lubrication is poor or the large cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the large cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the large cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the large cylinder center line. In this way, when the piston works in the large cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the large cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

If the large cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

Improve the service life of the large cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the large cylinder (such as the large cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the large cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the large cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single large cylinder exhaust.

The repair method of the large cylinder: the repair of the large cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

Answers to some questions about large cylinder:

What is the relationship between medium cylinder and side cylinder ratio of forklift truck?
The middle cylinder and the side cylinder seem to have no relationship, as long as the lifting speed required by the design can be ensured, but the diameter of the cylinder can not be too thin, so as to avoid the middle cylinder acting first when the high gantry vibration lifting, and then the two cylinders acting again.

How to select swing cylinder? Under what conditions are they designed and selected?
1, determine the system parameters: ① the weight and the required force; ② Nominal working pressure and range; ③ The time required to travel this distance; 4 oil medium 2, installation method: select the appropriate way for the specific application 3, cylinder diameter and working pressure: determine the cylinder diameter and provide the necessary force required by the system pressure 4, piston rod: determine the minimum piston rod diameter required to withstand the longitudinal bending force, select the appropriate piston rod end and piston rod end thread 5, piston: Whether the seal type is suitable for the application 6, buffer: choose the buffer requirements as appropriate.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
美女插逼观看| 美女鸡吧在线观看| 操死你蜜桃视频| 依兰县| 久久精品在一区不卡| 激情无月网址| 日韩免费视频在线一区二区三区四区| 日韩老肥逼| 久久亚洲av精| 女人的逼被插视频网站| 骚 逼 亚洲| 欧美日韩尻逼| 人妻少妇久久在线观看| 色呦呦网站一区二区| 看看免费国产大机吧操逼网站| 日本中文字幕5区| 亚洲综合欧美色五月俺也去三区| 久久爱不卡| 插美女91| 欧美成人在线日本邪恶又怕欧繁恒正在 | 天堂五月激情网| 日韩爱爱网页| 欧美丝袜视频一区二区| 轻轻干中文字幕| 神马中文一区| 人妻激情麻豆综合| 沙洋县| 精品熟女少妇一区二区三区| 国产1黄片| 黑老日欧美韩国老女人啪啪| 韩国三级片亚洲成人视频中文字幕| 国产人妻精品一区二区| 五月婷婷成人三级片| 亚洲一区二区三区在线极品| 最新一区视频网址| 丰满少妇人妻视频一区二区三区 | 极品美女被黑人大吊操| 日韩伦理免费观看一区二区三区视频| 黑丝五月天| 大鸡吧用力一点啊视频| 大香焦在线日韩|