亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hydraulic hollow cylinder Sold to Algeria

Release time:2023-12-18 10:57:21 Hits: Current position: Home > News

This article mainly introduces:

Algeria hydraulic cylinder,hydraulic hollow cylinder manufacturer,hydraulic hollow cylinder

Algeria hydraulic hollow cylinder

(Algeria hydraulic hollow cylinder,produced by Hengyu Group)

hydraulic hollow cylinder are widely used in Algeria,because of excellent temperature resistance,no need for deceleration device,long service life.So our company has designed hydraulic hollow cylinder for customers from Algeria.

Introduction to hydraulic hollow cylinder:

The hydraulic hollow cylinder should not be mixed with foreign objects during assembly, which will cause scars. Before the total assembly of the hydraulic hollow cylinder, all parts must be fully removed and cleaned. When the parts are installed with burrs or dirt, foreign objects are easily embedded into the surface of the hydraulic hollow cylinder wall due to the stiffness and the weight of the parts, causing scars.

When using the hydraulic hollow cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the hydraulic hollow cylinder block. If the hydraulic hollow cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the hydraulic hollow cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the hydraulic hollow cylinder, so that the working efficiency of the hydraulic hollow cylinder is reduced.

We can not just consider the price and ignore the quality when we purchase the hydraulic hollow cylinders. Now some manufacturers produce unqualified products in order to reduce costs, the piston rod is not adjusted, the rod coating is not enough, the hydraulic hollow cylinder finish can not reach, the guide sleeve should use copper, but instead of ductile iron, although the cost is reduced, the quality of the hydraulic hollow cylinder is not required.

After chrome plating of the piston rod of the hydraulic hollow cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

Answers to some questions about hydraulic hollow cylinder:

Is the hydraulic cylinder leaking because there is no pressure?
HC hydraulic cylinder common leakage reasons, first: most of the reasons are because the seal surface wear or aging leads to poor sealing, so there is no pressure to operate, as long as the piston seal can be replaced. Second: It may also be the piston rod strain, repair the piston rod is good. If it is because the piston strength is not enough and the playing time is long, it is necessary to replace the piston.

Why do two hydraulic cylinders lift out of sync?
There may be several situations (do not know the result of the equipment, may not be accurate) 1, whether the slow one is worn 2, whether there is air in the slow cylinder 3, if the two cylinders are supplied by the same oil port, whether the slow joint is blocked (some processing residue will reach a certain oil port under a certain coincidence condition, This situation will not happen if it is not necessarily good before) 4, the oil seal in the slow cylinder leaks, causing the feed oil to leak from the return oil end. Point 4 is most likely because it is invisible and a technical failure. If it is a dual oil feed (separate oil feed), it is also necessary to check the oil supply system and the oil return system (valve type).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
在哪里看免费操逼视频| 北岛玲一一区二区蜜桃| 成品人和精品一区二区| 日本石原莉奈一区二区三区 | 久久久不卡人妻一区二区| 激情影院东京热| 啪一啪五月婷| 无码一区二区高潮尿尿| 日美女的嫩逼逼| 在线观看caob| 操欧美大骚浪贱逼逼v| 操你b视频| 好吊视频一二三区大香蕉| 大香蕉久手机在线视频| 嗯嗯嗯啊啊啊啊啊啊啊啊啊在线观看| 国产免费网站久久白虎| 日本一区二区我不卡| 人体精品一二三区| /美女日逼免费视频| 国产成人偷拍一区| 91大神在线观看网| 欧美日韩国产最新在线| 国产久久呦呦精品视频| 不卡的日韩欧美| 色诱黄片国产| 日本老妇wBBHDw69一区| 69精品国产人妻国产毛片| 日本在线视频大香蕉| 美女被戳屁股黄污污| 婷婷久久涩涩| 91性奴调教在线| 大鸡巴插大逼里的高清视频| 台湾天天插天天日| 大鸡巴大战小骚逼| 美女小穴永久免费在线观看| 熟女无码在线首页| 美女18禁高清无码| 国产人妻精品八区九区十区| 微拍福利一区福利二区| 欧美一区两区| 亚洲熟女精品视频|