亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

plunger type cylinder Sold to Ecuador

Release time:2023-12-12 10:13:54 Hits: Current position: Home > News

This article mainly introduces:

Ecuador hydraulic cylinder,plunger type cylinder manufacturer,plunger type cylinder

Ecuador plunger type cylinder

(Ecuador plunger type cylinder,produced by Hengyu Group)

plunger type cylinder are widely used in Ecuador,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed plunger type cylinder for customers from Ecuador.

Introduction to plunger type cylinder:

Regular maintenance of the plunger type cylinder includes: regular tightening, plunger type cylinder fastening screws and gland screws, plunger type cylinder piston rod stop adjustment screws, should be tightened once a month, tighten each screw evenly, and achieve the corresponding tightening torque. Replace the seal regularly, it is recommended to replace the seal of the plunger type cylinder once a year. Clean regularly, the plunger type cylinder is cleaned every other year, and the seals are replaced while cleaning.

plunger type cylinder hydraulic oil selection: The recommended working oil viscosity of the plunger type cylinder is 10 ~ 110cSt (1.8 ~ 15E), ISO VG46 hydraulic oil. The normal working oil temperature is 10 ~ 70℃, and the ambient temperature is in the range of -20 ~ 80℃. When the ambient temperature and service temperature are low, the hydraulic oil with lower viscosity can be selected.

The quality of the plunger type cylinder can not be ignored in the purchase of the plunger type cylinder. The plunger type cylinder is the main component of the plunger type cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. plunger type cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of plunger type cylinder is deep hole processing, which has always troubled the processing personnel.

The main role of the plunger type cylinder: the plunger type cylinder is an executive element in the hydraulic transmission system, which is an energy conversion device that converts hydraulic energy into mechanical energy. The hydraulic motor realizes continuous rotary motion, while the plunger type cylinder realizes reciprocating motion. The structure of the plunger type cylinder has three categories: piston plunger type cylinder, plunger plunger type cylinder, swing plunger type cylinder, piston plunger type cylinder and plunger plunger type cylinder to achieve reciprocating linear motion, output speed and thrust, swing plunger type cylinder to achieve reciprocating swing, output angular speed (speed) and torque. In addition to the single use of the plunger type cylinder, two or more can be combined or used in combination with other mechanisms. To fulfill a special function. The plunger type cylinder has simple structure and reliable operation, and has been widely used in the hydraulic system of machine tools.

Answers to some questions about plunger type cylinder:

Is there a national standard for the testing of hydraulic cylinders?
Generally speaking, the cylinder test is carried out according to JB/JQ20302 Allowable leakage of cylinder in pre-factory leakage test. GB2879 hydraulic cylinder piston and piston rod dynamic seal groove type, size and tolerance. GB6578 hydraulic cylinder piston rod dust ring groove type, size and tolerance. GB7938 hydraulic cylinder and cylinder nominal pressure series, etc.

Why does the cylinder pop out of itself when it stops?
This situation has two possibilities, 1. There is more air in the system, so exhaust the gas. 2. The back pressure of the oil return is relatively large, check the oil return filter, check whether the cylinder has a rod cavity buffer is too tight, and choose a 3-position 4-way M-type valve for the reversing valve. In addition, after the shutdown, manually change the reversing valve back and forth several times, it should not rise out.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
九一.一区| 色婷婷天天操| 久久日韩制服丝袜人妻| 老骚逼午夜AV| 国产在线视频=一区| 美女叉鸡A| 日韩国产aV嫩色aV一区二区| 日韩成人激情av| 大 几巴 爽 帅哥 哦哦 操| 欧美女人日B视频| 你懂的亚洲无码肛交| 三级AV操逼| 男人的天堂AVAV在线| 国产精品探花一区二区三区| 情侣偷拍福利视频| 欧美大鸡巴操熟妇| 诱惑91啦| 亚洲天堂午夜场| 深夜激情五月婷| 东北老骚妇操b视频| 东京热亚州无码AV| 丝袜黄片视频国产免费| 昌乐县| 亚洲欧美制服第一页综合| 国产精品一级AV免费片| 最新制服丝袜手机在线| 一之本道国产精品高清懂色| 国产AV嫩逼HD| 欧美激情骚逼| 美女脱光日逼| 国产精品高潮呻吟久| 操老逼视频免费播放| 加勒比东京热成人一区| 黄色电影之青青草视频| 国产成人在线一级 二级 三级| 五月天色一区二区日韩精品| 丁香婷婷色8XXX6799视频| 人妻丝袜激情| 啊啊啊啊啊啊视频一区| 超碰大香蕉资源| 操日本熟妇逼|