亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reciprocating cylinder Sold to Pakistan

Release time:2023-12-12 10:13:48 Hits: Current position: Home > News

This article mainly introduces:

Pakistan hydraulic cylinder,reciprocating cylinder manufacturer,reciprocating cylinder

Pakistan reciprocating cylinder

(Pakistan reciprocating cylinder,produced by Hengyu Hydraulic Cylinder Factory)

reciprocating cylinder are widely used in Pakistan,because of no need for deceleration device,long service life,smooth movement.So our company has designed reciprocating cylinder for customers from Pakistan.

Introduction to reciprocating cylinder:

reciprocating cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the reciprocating cylinder head itself is the guide sleeve of the piston rod, the reciprocating cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the reciprocating cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

Do not regularly check the damage of the chrome layer of the reciprocating cylinder: completely extend the reciprocating cylinder and carefully check whether there is any surface damage such as injury, strain, welding slag, such as the surface damage position, in the reciprocating cylinder block < 20cm, and the damage depth < 5mm, should be repaired in time to prevent long-term damage to the reciprocating cylinder seal. Welding slag is strictly prohibited on the surface of the reciprocating cylinder.

If the reciprocating cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the reciprocating cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow reciprocating cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the reciprocating cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the reciprocating cylinder includes the leakage caused by excessive wear of the reciprocating cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and reciprocating cylinder, and the phenomenon of "pulling the reciprocating cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

When installing the reciprocating cylinder pipe, the pipe should be cleaned after installation, and should not pass through the reciprocating cylinder block, and the by-pass pipe must be installed in front of the oil port of the reciprocating cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the reciprocating cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the reciprocating cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Answers to some questions about reciprocating cylinder:

What is a differential cylinder?
The differential cylinder is by connecting the return oil of the rod cavity through the pipeline, allowing them to flow into the rodless cavity, thereby speeding up the extension speed of the piston rod. In fact, the cylinder is still the cylinder, but the oil circuit is related to the connection. The oil connection mode in which both chambers of a single rod hydraulic cylinder are fed hydraulic oil is called differential connection.

Servo cylinder control principle
The electro-hydraulic pulse servo cylinder is composed of a stepper motor, a three-position four-way servo valve, a mechanical feedback device (a wire carrier) and an oil lever. When the stepper motor gets a pulse signal, its output shaft rotates 1.5 or 3 degrees, the servo valve spool drives the wire to rotate at the same time, the valve spool moves and opens the reversing cylinder to output pressure oil, the piston moves and drives the lead screw to reverse rotate the valve spool back to the original position, and the servo valve stops output pressure oil in the center. At this time, the cylinder moves 0.1 or 0.2mm stroke, and the displacement and speed of the cylinder travel are determined according to the given value of the electrical pulse.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
操操操16p| 欧美日韩少妇熟女| 色欲蜜臀AV 一区二区| 正在播放日韩av| 亚洲av美女一区二区| 国产色老熟女| 精品乱子伦一区二区三区毛| 欧美激情。91| 超碰区在线| 做暧暧欧美日韩| 人妻偷人视频一区二区| 男人看片av网站| 少妇被领导玩呻吟声太大| 欧美日韩新片| 插逼逼视频网站| 无广告熟女网站| 广元市| 亚洲熟女少区二区三区| 中文字幕特一区二区三区| 爆操中国美女| 天天操夜夜操天天操天天操| 被操的啊啊啊啊在线| 有码在线vcd| 丰满美女艹B视频| 麻花91麻豆| 嗯嗯嗯啊啊啊欧美视频| 99热日本精品| 几把插美女的逼的免费视频| 五月婷婷做了爱了| 疯狂操美女白虎网站| 3d动漫福利啪啪的| 久久久久中文老师视频| 好骚好爽好骚| 欧美色白虎逼| 国产另类老骚逼视频| 骚逼无马操| 免费看日粉嫩B视频| AV高清插逼逼| 超碰免费视屏日本| 日本在线不卡视频久久| 涩一把91|