亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stacker cylinder Sold to Oman

Release time:2023-12-12 10:13:47 Hits: Current position: Home > News

This article mainly introduces:

Oman hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

Oman stacker cylinder

(Oman stacker cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stacker cylinder are widely used in Oman,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed stacker cylinder for customers from Oman.

Introduction to stacker cylinder:

How to determine the working pressure of the stacker cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, stacker cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

stacker cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the stacker cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

The scar on the sliding surface of the stacker cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the stacker cylinder wall. Therefore, before installation, these scars must be fully repaired.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the stacker cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

Answers to some questions about stacker cylinder:

How to select swing cylinder? Under what conditions are they designed and selected?
1, determine the system parameters: ① the weight and the required force; ② Nominal working pressure and range; ③ The time required to travel this distance; 4 oil medium 2, installation method: select the appropriate way for the specific application 3, cylinder diameter and working pressure: determine the cylinder diameter and provide the necessary force required by the system pressure 4, piston rod: determine the minimum piston rod diameter required to withstand the longitudinal bending force, select the appropriate piston rod end and piston rod end thread 5, piston: Whether the seal type is suitable for the application 6, buffer: choose the buffer requirements as appropriate.

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
丁香五月婷婷av| 特黄特黄无吗污在线观看点击入内 | MIDV中文字幕一区二区| 中文字幕幕久久久| 真实3p人妻| 美女操B阍黄色| 中国老妓女AV| 久久麻豆产精亚洲AV果冻| 亚洲性爱~去干网| 韩国人妻激情在线| 美女干逼aV| 欧美大鸡巴操日本美女逼| 好爽免费日本| 熟女人妻人妻AV| 丁香啪啪激情| 国产成人精一二三区熟女| 欧美一级家庭夫妻高潮视频| 78精品一区二区| 俄罗斯日B视频| 美女被大鸡巴桶高潮| 日韩久久成人视频| 欧美日韩免费一区二区三区波多野结衣| 国产精选AV片| 亚洲一区二区三区啊啊啊啊痛| 欧洲熟女大香蕉| 青青草按摩婷婷五月| 惠水县| 国产少妇欧美| 日本免费福利一区二区| 岚皋县| 国产熟女av在线观看| 做暧暧小视频久久九九青青操 | 亚洲 日本 欧美 日韩精品| 一道本高清无码不卡在线观看| 欧美裸体无码精品| 超大机巴操小逼高清视频| 宝宝v啊嗯视频| 国产AV不齐一二三四区| 激情五月播播| www.御姐在线播放| 逼情久久|