亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reset cylinder Sold to Denmark

Release time:2023-12-12 10:13:43 Hits: Current position: Home > News

This article mainly introduces:

Denmark hydraulic cylinder,reset cylinder manufacturer,reset cylinder

Denmark reset cylinder

(Denmark reset cylinder,produced by Hengyu Hydraulic Cylinder Factory)

reset cylinder are widely used in Denmark,because of long service life,smooth movement,high work efficiency.So our company has designed reset cylinder for customers from Denmark.

Introduction to reset cylinder:

The difference between the plunger reset cylinder and the piston reset cylinder is that the piston in the reset cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type reset cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

If the reset cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the reset cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow reset cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the reset cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the reset cylinder includes the leakage caused by excessive wear of the reset cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and reset cylinder, and the phenomenon of "pulling the reset cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

If the seal of the reset cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

The wear of the hard chromium plating layer of the reset cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

Answers to some questions about reset cylinder:

How to repair if hydraulic shears cylinder oil leakage?
The hydraulic cylinder is generally disassembled and the sealing ring is replaced. There are generally two ways to install the ends of the hydraulic cylinder. The larger hydraulic cylinder is mostly flanged disc type, which is screwed to the middle cylinder block by several bolts, the bolts are removed, and the cylinder head is slowly pulled out. The smaller hydraulic cylinder, the cylinder block and the head itself are threaded, and the rotating end cap can be removed from the cylinder block. If you do not understand the hydraulic cylinder, it is best to ask someone to deal with it. It is easy to damage the sealing ring and internal surface during disassembly.

What brand of hydraulic cylinder seal ring is best?
Depending on the specific product, the world famous seal brands are NOK, CFW, PARKER, TSS, WKF, DINGZING DZ, ASTON, HALLITE, TECNOLAN and so on.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚欧操逼的视频免费观看| 成年男女福利视频| 欧美国精产品成人专区| 欧美熟女相奸| 日本久久网捆绑强奸视频| 特级Av毛片一区二区三区| 日韩 欧美 视频一区 纸飞机| 靖西县| 大鸡巴日逼毛片| 操人妻美女熟妇| 国产 欧洲视频欧洲1| 一区二区AV网址| 免费深喉口爆成人导航| 北条麻妃作品视频在线观看| 操美女一区在线| 美日韩少妇| 少妇人妻a婷亚| 制服诱惑丝袜中文字幕| 国产精品剧情欧美日韩高清| 芊芊久久精品无码| 国产裸体区二区| 在线观看中文字幕avav| 欧美日韩一二三四区| 五月天激情黄片| 精品一=三一区| 啪啪啊啊啊视频| 操逼爽片视频| 无圣光在线三区| 女逼视频网| 欧美 人妻 91 视频| 熟女一区二区三区丝袜| 欧美精品色色色| 操逼毛多美女| 鱼台县| 私拍二区| 久久亚洲一区二区丝袜内裤| 91蜜桃传媒精品久久久一区二区| 日本又大又黄又粗| 日本一区 黄色| 骚鸡巴插入骚臀高潮| 白丝美女被操得连连叫 |