亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

jack cylinder Sold to Peru

Release time:2023-12-09 16:24:35 Hits: Current position: Home > News

This article mainly introduces:

Peru hydraulic cylinder,jack cylinder manufacturer,jack cylinder

Peru jack cylinder

(Peru jack cylinder,produced by Hebei Hengyu company)

jack cylinder are widely used in Peru,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed jack cylinder for customers from Peru.

Introduction to jack cylinder:

If the jack cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the jack cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow jack cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the jack cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the jack cylinder includes the leakage caused by excessive wear of the jack cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and jack cylinder, and the phenomenon of "pulling the jack cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

When the jack cylinder is customized, if there are high requirements for the quality of the jack cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the jack cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the jack cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

Factors that should be considered when selecting the oil seal in the jack cylinder: some specific factors should be taken into account when selecting the oil seal in the jack cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: jack cylinder diameter, piston rod diameter, piston rod and piston groove size, jack cylinder working pressure, jack cylinder movement speed, hydraulic system oil temperature and jack cylinder working environment.

Before purchasing the jack cylinder, it is necessary to master the original information and design basis, mainly including: the use and working conditions of the machine; The structural characteristics, load conditions, stroke size and operation requirements of the working mechanism; The selected working pressure and flow of the hydraulic system; The reality of materials, fittings and processes; Relevant national standards and technical specifications, etc.

Answers to some questions about jack cylinder:

What is the problem that the cylinder stroke is not in place?
1. Mechanical cause: the piston rod bends; If there is a synchronous cylinder, the stroke of the two cylinders may be different. 2. Hydraulic reason: the system back pressure is too large; The actuator load increases while the system pressure decreases. The electric is not sent, the reversing valve is not reset or stuck, the oil is too dirty, there is gas in the system, the external inertia load is too large, and the cylinder stroke is not in place.

Can one hydraulic pump with two cylinders work?
A hydraulic pump with two cylinders will work. Commonly used hydraulic pump types: 1, according to whether the flow can be adjusted can be divided into: variable pump and quantitative pump. The output flow can be adjusted according to the needs of the variable pump, the flow can not be adjusted called quantitative pump. 2, according to the pump structure commonly used in the hydraulic system is divided into: gear pump, vane pump and plunger pump 3 kinds. Gear pump: small volume, simple structure, the cleanliness of the oil requirements are not strict, the price is cheaper; However, the pump shaft is subjected to unbalanced force, serious wear and leakage. Vane pump: divided into double acting vane pump and single acting vane pump. The pump has uniform flow, smooth operation, low noise, higher pressure and volumetric efficiency than gear pump, and more complex structure than gear pump.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
婷婷五月在线激情综合| 国产精品 国产传媒 高清不卡| 日本大香蕉黄色片| 久久六十熟女| 日本五十路熟女中文字幕中出| 色幼国产精品| 你懂的日韩专区| 操美女B呦呦| 日韩伦理第一区第二区| 成人 啊啊啊啊 不要啊| 亚洲看靠逼视频的网站| 轮奸处女高潮一区二区| 中文字幕一区二区二三区四区69| 精品AⅤ一二三区| 国产有码一二三四五六七区| 中文字幕人妻熟女二区| 三级片不伦人妻中出| 亚洲福利老司机| 国产精品视频一区竹菊| 日本一区二区资源在线| 一直草在线观看中文字幕在线| 日韩美免费观看视频| 婷婷激情九月| 天天干天天操美女夜夜| 操外国美女| 嗯操三级片一区二区三区| 18禁自拍网站| www.国产精品人妻精品AV| 欧美日韩综合人妻丝袜偷拍| 巴 国产精品| 91大神在线播放第二页| 金秀| 熟女的老骚91| 青青在线一区二区视频| bt1024最新合集字幕亚洲天堂| av资源草草草草草草| 91香蕉快色999| 欧美大黑鸡巴操女网| 爽歪歪精品视频| av资源每日更新| renqichaopeng|