亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steel mill cylinder Sold to Sri Lanka

Release time:2023-12-08 14:41:35 Hits: Current position: Home > News

This article mainly introduces:

Sri Lanka hydraulic cylinder,steel mill cylinder manufacturer,steel mill cylinder

Sri Lanka steel mill cylinder

(Sri Lanka steel mill cylinder,produced by Hengyu Hydraulic Cylinder Factory)

steel mill cylinder are widely used in Sri Lanka,because of long service life,smooth movement,high work efficiency.So our company has designed steel mill cylinder for customers from Sri Lanka.

Introduction to steel mill cylinder:

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the steel mill cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

steel mill cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the steel mill cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the steel mill cylinder. c. The steel mill cylinder seal is extruded, if the O-ring is obviously extruded at the steel mill cylinder seal, replace the steel mill cylinder seal.

The difference between the plunger steel mill cylinder and the piston steel mill cylinder is that the piston in the steel mill cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type steel mill cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

The oil steel mill cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

Answers to some questions about steel mill cylinder:

How to limit cylinder push rod rotation?
In general, the push-rod rotation can be limited after the push-rod is connected to the pushed mechanism. For example, the push rod is hinged with the push mechanism, or the push mechanism itself is guided, which can limit the rotation of the push rod.

What type of seal is the cylinder of shaft 50?
You won't know the exact model until you take it apart. Oil seals have O, Y, Yx, KYx, U, UN, UHS, YA, St, Gray, Yamagata, Lei type, etc. It is difficult to know what kind of oil seal the designer chooses. Cylinder oil seal installation method: 1. Receive a fixed number of oil seals. 2. From receiving the oil seal to assembly, it must be kept clean. 3. Before assembly, check the oil seal and measure whether the size of each part of the oil seal is consistent with the size of the shaft and cavity. Before the oil seal is installed, the size of the shaft diameter should be clearly compared with the inner diameter of the oil seal. The inner cavity size should be suitable for the outer diameter width of the oil seal. Check the lip of the oil seal for damage.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
中文字幕精品一区二区三区不卡| 蜜臀av操美女人妻| 嗯嗯,天天擦人妻| 不卡素人国产| 日韩操老逼| 搞鸡巴在线| 三上有亚久久一区| 国产精品秘果冻传媒AV| 人妻大屁股在线后入| 超碰AV电影在线观看| 91久久人人澡人人添人人爽| 欧美天天橾| 中文字幕乱伦区二区三区| 日高潮喷水久久| www.久久操B| 亚洲AV中午一区二区三区| 騷逼1區| 行唐县| 欧美操逼鸡巴| 熟女少妇一二区| 国产的一级a爱免费看| 手机黄片.cod| 亚洲操逼网址| 欧美高清大胆视频在线看| 性感大鸡巴操美女小骚逼大骚逼骚逼逼| 中文字幕在线视频二区| 大鸡巴插入女人的鸡巴视频| 二区在线不卡视频| 超碰公开免费国产在线观看| 绝顶抽插av| 亚洲少妇熟女一区二区三区| 熟女性视频| 女同,另类,重口二区| 婷婷在线播放大香蕉| 色哟哟激情视频| 大香蕉手机性爱视频| 黑人大鸡巴操逼大猛片| 亚洲一区九九热精品一本道| 波多野结衣日韩在线| 捅美女鸡鸡免费视频网站| 成人人妻欧美一区免费二区三区|