亚洲色图10p,xxx.,欧美日韩国产激情一区二区三区,久久久久人妻精品一区二区三区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

plunger type cylinder Sold to Germany

Release time:2023-12-08 14:41:32 Hits: Current position: Home > News

This article mainly introduces:

Germany hydraulic cylinder,plunger type cylinder manufacturer,plunger type cylinder

Germany plunger type cylinder

(Germany plunger type cylinder,produced by Hengyu Hydraulic Co., Ltd)

plunger type cylinder are widely used in Germany,because of no need for deceleration device,smooth movement,excellent temperature resistance.So our company has designed plunger type cylinder for customers from Germany.

Introduction to plunger type cylinder:

The assembly work of the plunger type cylinder has a great impact on the quality of the plunger type cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

When the piston speed of the plunger type cylinder is high, the steel ball of the check valve flows with the oil flow, so that the valve hole is blocked, and the plunger type cylinder moves irregularly. Elimination method: Replace the steel ball with a cone valve or spool with a guide shoulder.

The internal leakage of the plunger type cylinder should be prevented when the plunger type cylinder is used. The internal leakage of plunger type cylinder includes the leakage caused by excessive wear of plunger type cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

If it is found that the plunger type cylinder lubrication is poor or the plunger type cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the plunger type cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the plunger type cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the plunger type cylinder center line. In this way, when the piston works in the plunger type cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the plunger type cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

Answers to some questions about plunger type cylinder:

Why is the hydraulic cylinder of the larger excavator arm upside down?
The weight of the excavating arm of a large excavator will be very heavy, and an oil cylinder has two cavities, one is a rod cavity, and the other is a rodless cavity. The lifting force of the excavator is the product of the ortho-projection area of the piston rod cavity by the oil pressure, so the strength of the rodless cavity is much greater than that of the rod cavity. And the parallel bars with the piston rod facing down are also conducive to assembly and future maintenance. So a large excavator has to keep the cylinder facing down.

Slide weight 35 kg exit stroke 55mm, is it suitable to use 40 cylinder diameter cylinder?
The maximum output force of the 40-bore hydraulic cylinder can reach 2 tons, and whether it can be used depends on the use scenario. In addition, the problem of mechanism stuck has nothing to do with the size of the power source, and reasonable structural design and good machining and assembly accuracy are the key.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
oumeibibi| 婷婷久久六月激情 | 又粗又长又硬的大鸡巴艹屄视频 | 亚洲韩国性爱视频网站| 正在操逼女人| 熟妇大鸡巴操爽了| 91大神亚洲网黄| 清纯校花裸体被操视频在线观看| 骚逼视频网站啊啊啊| 人妻偷人26p| 沛县| 成人福利在线看| AV高清插逼逼| 一区二区三区四区在线观看国产日韩| 亚洲诱惑视频| av网站中出| 日中性视频一区三区色| 大鸡巴日小骚逼动态视频| 亚洲操逼毛片| 女同舌吻成人视频18禁| 精品香蕉福利导航| 新红楼AV在线| 国产人妻人伦精品1国产丝袜| 亚洲中文婷婷| 极品馒头无码一区二区| 视频欧美人妻日韩| 欧美日bAv| 插老师嗯嗯蜜臀视频国产视频| 一本道中文字幕高清无码| 熟妇大屁屁一区二区三区| 国产丝袜美女精品AV| 祥仔Av每日更新| 欧美一区免费观看视频| 神马日韩一区| 欧美久久久成人在线视频| 91超级人人人人人妻| 枫花恋av一级观看| 美女精品视频网站| 这里只有精品婷婷五月| 一区二区三区四区五区性爱无码中文字幕 | 白丝被爆操视频播放在线观看的人|